Hi Mark, viq, did either of you get it to work with the virtual table?
Mine mostly works with:
action "lmtp-local" mda "/usr/libexec/mail.lmtp -d
unix:/var/dovecot/lmtp -f %{sender} %{rcpt}" virtual <virtuals>
but it ignores the virtual table completely.
If I miss out the ${rcpt}, I get a no recipient specified and if I have
the {user.username} it gives a similar error.
Did your virtual<vusers> work or am I doing something daft?
Regards - Nick
On 27/05/2018 08:51, viq wrote:
> On 18-05-27 09:34:10, Mark Patruck wrote:
>> For me it works with %{user.username} as mail.lmtp(8) user.
>>
>> See "FORMAT SPECIFIERS" in smtpd.conf(5) for details.
>
> Shows how well I read the man page.... With this it works, thank you!
>
>> On Sun, May 27, 2018 at 09:04:56AM +0200, viq wrote:
>> > On 18-05-26 19:18:56, Edgar Pettijohn III wrote:
>> > >
>> > > > Sorry, I've read the announcements, looked at man pages and examples,
>> > > > but still didn't manage to figure out how to translate "deliver via dovecot
>> > > > lmtp"
>> > > > (to have sieve working) into the new syntax. So far my config was:
>> > > >
>> > > > table vusers ldap:/etc/mail/ldap.conf
>> > > > table vdomains ldap:/etc/mail/ldap.conf
>> > > > table passwd ldap:/etc/mail/ldap.conf
>> > > >
>> > > > accept from local for local virtual <vusers> deliver to lmtp
>> > > > "/var/dovecot/lmtp"
>> > > > accept from any for domain <vdomains> virtual <vusers> deliver to lmtp
>> > > > "/var/dovecot/lmtp"
>> > > >
>> > > >
>> > > > I tried changing those into:
>> > > >
>> > > > action "lmtp-local" mda "/usr/libexec/mail.lmtp -d /var/dovecot/lmtp"
>> > >
>> > > try:
>> > > action "lmtp-local" mda "/usr/libexec/mail.lmtp -d unix:/var/dovecot/lmtp -f
>> > > %{sender}"
>> >
>> > Well, this time I'm getting
>> > result=TempFail stat=Error ("mail.lmtp: no recipient was specified")
>> > so there's difference. So I tried
>> > action "lmtp-local" mda "/usr/libexec/mail.lmtp -d unix:/var/dovecot/lmtp -f %{sender} %{recipient}" virtual <vusers>
>> > but that resulted in
>> > result=TempFail stat=Error ("smtpd: mda command line could not be expanded: Interrupted system call")
>> > same with %{rcpt-to}
>> >
>> > Where did you get the %{} syntax? I haven't seen it anywhere when
>> > reading about this.
>> >
>> > > However, this does feel odd. I need to switch over as well, but still trying
>> > > to wrap my brain around the new config.
>> > > > virtual <vusers>
>> > > > action "relay" relay
>> > > > match from local for local action "lmtp-local"
>> > > > match from any for domain <vdomains> action "lmtp-local"
>> > > > match from local for any action "relay"
>> > > >
>> > > >
>> > > > but delivery attempts fail with Error ("mail.lmtp: sender must be specified
>> > > > with -f")
>> > > >
>> > > > What would be the proper config for this?
>> > > > --
>> > > > viq
>> > >
>> >
>>
>> --
>> Mark Patruck ( mark at wrapped.cx )
>> GPG key 0xF2865E51 / 187F F6D3 EE04 1DCE 1C74 F644 0D3C F66F F286
>> 5E51
>>
>> http://www.wrapped.cx
No comments:
Post a Comment