On Tue, Feb 27, 2018 at 04:53:06PM -0700, j@bitminer.ca wrote:
> I am replacing my ancient X60 with an X130e of lesser age. This model is
> previously found as working on misc.
>
> When trying to install 6.2 (release) over Windows 10 there is no video to
> see.
>
> By booting miniroot62.fs from USB the kernel loads, but the "OpenBSD 6.2
> ...." and subsequent boot messages do not appear. The video is blank
> (apparently backlit but no text is present.) The biosboot loader messages
> prior to that do appear for a few seconds. The USB stick activity light
> does blink as if things are happening normally.
>
> Same result for 6.1 and 5.9.
>
> The three video options: Native video, VGA and HDMI video outputs show the
> same biosboot lines and then the screen blanks. A couple of different
> monitors on the VGA output show "unsupported format" or somesuch suggesting
> the video signal is not a standard format.
>
> There is no serial port on this hardware. The BIOS is updated to the
> latest. I'm going to try to obtain a dmesg with blindly typing against the
> install script (blessed OpenBSD with a simple install CLI!)
>
> I'm wondering if there is something to be enabled/disabled in boot_config
> that would help. I don't quite understand why video would blank out once
> the kernel gets control (src/sys/arch/amd64/amd64/consinit.c and machdep.c)
> since nothing looks like it is touching video configuration. This seems to
> be way before any video driver gets control.
>
> The Windows 10 "about" page says this is AMD E-450 APU with Radeon HD
> Graphics. The Hardware page says "AMD Radeon HD 6320 Graphics".
>
> Does anyone have further advice?
>
> thanks
>
> John
>
My x130e has no problems booting -current miniroot62.fs from USB.
Video works fine ("ATI Radeon HD 6310"). dmesg below.
Did you boot from OpenBSd powered-off state or soft reboot after running
Windows? It's possible that Windows leaves devices in a state where
OpenBSD cannot use them.
BTW this machine used to be an E-450 as well, however something broke
on the mainboard so the system would not see the battery anymore.
At the time I could only find an E-300 mainboard to replace it but it's
been working fine since.
OpenBSD 6.2-current (RAMDISK_CD) #11: Tue Feb 27 17:20:47 MST 2018
deraadt@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/RAMDISK_CD
real mem = 3849388032 (3671MB)
avail mem = 3728969728 (3556MB)
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.6 @ 0xf9d00 (58 entries)
bios0: vendor LENOVO version "8RET52WW (1.15 )" date 11/15/2011
bios0: LENOVO 305162G
acpi0 at bios0: rev 4
acpi0: tables DSDT FACP SLIC HPET APIC MCFG UEFI UEFI SSDT SSDT UEFI
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: AMD E-300 APU with Radeon(tm) HD Graphics, 1297.51 MHz
cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,MWAIT,SSSE3,CX16,POPCNT,NXE,MMXX,FFXSR,PAGE1GB,RDTSCP,LONG,LAHF,CMPLEG,SVM,EAPICSP,AMCR8,ABM,SSE4A,MASSE,3DNOWP,IBS,SKINIT,ITSC
cpu0: 32KB 64b/line 2-way I-cache, 32KB 64b/line 8-way D-cache, 512KB 64b/line 16-way L2 cache
cpu0: 8 4MB entries fully associative
cpu0: DTLB 40 4KB entries fully associative, 8 4MB entries fully associative
cpu0: apic clock running at 199MHz
cpu0: mwait min=64, max=64, IBE
cpu at mainbus0: not configured
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 21, 24 pins
, remapped to apid 2
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus -1 (PB4_)
acpiprt2 at acpi0: bus 1 (PB5_)
acpiprt3 at acpi0: bus 2 (PB6_)
acpiprt4 at acpi0: bus 3 (PB7_)
acpiprt5 at acpi0: bus 4 (P2P_)
acpiprt6 at acpi0: bus -1 (SPB0)
acpiprt7 at acpi0: bus -1 (SPB1)
acpiprt8 at acpi0: bus -1 (SPB2)
acpiprt9 at acpi0: bus -1 (SPB3)
acpiec0 at acpi0
acpicpu at acpi0 not configured
acpitz at acpi0 not configured
"PNP0C0C" at acpi0 not configured
"PNP0C0E" at acpi0 not configured
"LEN0026" at acpi0 not configured
"LEN0068" at acpi0 not configured
"ACPI0003" at acpi0 not configured
"PNP0C0A" at acpi0 not configured
"PNP0C0D" at acpi0 not configured
"PNP0C14" at acpi0 not configured
"PNP0C14" at acpi0 not configured
"PNP0C14" at acpi0 not configured
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "AMD AMD64 14h Host" rev 0x00
vga1 at pci0 dev 1 function 0 "ATI Radeon HD 6310" rev 0x00
wsdisplay1 at vga1 mux 1: console (80x25, vt100 emulation)
"ATI Radeon HD 6310 HD Audio" rev 0x00 at pci0 dev 1 function 1 not configured
ppb0 at pci0 dev 5 function 0 "AMD AMD64 14h PCIE" rev 0x00: msi
pci1 at ppb0 bus 1
rtwn0 at pci1 dev 0 function 0 "Realtek 8188CE" rev 0x01: msi
rtwn0: MAC/BB RTL8188CE, RF 6052 1T1R, address 9c:b7:0d:e1:11:6d
ppb1 at pci0 dev 6 function 0 "AMD AMD64 14h PCIE" rev 0x00: msi
pci2 at ppb1 bus 2
alc0 at pci2 dev 0 function 0 "Attansic Technology L1D" rev 0xc0: msi, address 04:7d:7b:31:00:6e
atphy0 at alc0 phy 0: AR8035 10/100/1000 PHY, rev. 0
ppb2 at pci0 dev 7 function 0 "AMD AMD64 14h PCIE" rev 0x00: msi
pci3 at ppb2 bus 3
rtsx0 at pci3 dev 0 function 0 "Realtek RTS5209 Card Reader" rev 0x01: msi
sdmmc0 at rtsx0: 4-bit, dma
ahci0 at pci0 dev 17 function 0 "ATI SBx00 SATA" rev 0x00: apic 2 int 19, AHCI 1.2
ahci0: port 0: 3.0Gb/s
scsibus0 at ahci0: 32 targets
sd0 at scsibus0 targ 0 lun 0: <ATA, SanDisk SDSSDP12, 2.0.> SCSI3 0/direct fixed naa.5001b4496652afc1
sd0: 122104MB, 512 bytes/sector, 250069680 sectors, thin
ohci0 at pci0 dev 18 function 0 "ATI SB700 USB" rev 0x00: apic 2 int 18, version 1.0, legacy support
ehci0 at pci0 dev 18 function 2 "ATI SB700 USB2" rev 0x00: apic 2 int 17
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "ATI EHCI root hub" rev 2.00/1.00 addr 1
ohci1 at pci0 dev 19 function 0 "ATI SB700 USB" rev 0x00: apic 2 int 18, version 1.0, legacy support
ehci1 at pci0 dev 19 function 2 "ATI SB700 USB2" rev 0x00: apic 2 int 17
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "ATI EHCI root hub" rev 2.00/1.00 addr 1
"ATI SBx00 SMBus" rev 0x42 at pci0 dev 20 function 0 not configured
"ATI SBx00 HD Audio" rev 0x40 at pci0 dev 20 function 2 not configured
"ATI SB700 ISA" rev 0x40 at pci0 dev 20 function 3 not configured
ppb3 at pci0 dev 20 function 4 "ATI SB600 PCI" rev 0x40
pci4 at ppb3 bus 4
pchb1 at pci0 dev 24 function 0 "AMD AMD64 14h Link Cfg" rev 0x43
pchb2 at pci0 dev 24 function 1 "AMD AMD64 14h Address Map" rev 0x00
pchb3 at pci0 dev 24 function 2 "AMD AMD64 14h DRAM Cfg" rev 0x00
pchb4 at pci0 dev 24 function 3 "AMD AMD64 14h Misc Cfg" rev 0x00
pchb5 at pci0 dev 24 function 4 "AMD AMD64 14h CPU Power" rev 0x00
pchb6 at pci0 dev 24 function 5 "AMD AMD64 14h Reserved" rev 0x00
pchb7 at pci0 dev 24 function 6 "AMD AMD64 14h NB Power" rev 0x00
pchb8 at pci0 dev 24 function 7 "AMD AMD64 14h Reserved" rev 0x00
usb2 at ohci0: USB revision 1.0
uhub2 at usb2 configuration 1 interface 0 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb3 at ohci1: USB revision 1.0
uhub3 at usb3 configuration 1 interface 0 "ATI OHCI root hub" rev 1.00/1.00 addr 1
isa0 at mainbus0
pckbc0 at isa0 port 0x60/5 irq 1 irq 12
pckbd0 at pckbc0 (kbd slot)
wskbd0 at pckbd0: console keyboard, using wsdisplay1
umass0 at uhub0 port 1 configuration 1 interface 0 "vendor 0x090c product 0x1000" rev 2.00/10.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <, , > SCSI0 0/direct removable serial.090c1000083153020039
sd1: 3801MB, 512 bytes/sector, 7784448 sectors
"Image Processor Integrated Camera" rev 2.00/41.64 addr 2 at uhub1 port 5 not configured
"Broadcom Corp Broadcom Bluetooth Device" rev 2.00/7.48 addr 2 at uhub2 port 4 not configured
softraid0 at root
scsibus2 at softraid0: 256 targets
root on rd0a swap on rd0b dump on rd0b
No comments:
Post a Comment