On Sun, Jun 25, 2017 at 11:56:13AM +0200, Antoine Jacoutot wrote:
> On Sat, Jun 24, 2017 at 11:49:40AM -0500, rehcla wrote:
> > Hi Antoine,
> >
> > I can confirm that the Plugin installation works now for me:
> >
> > cd plugin_tmp/
> > /local/bin/python2.7 plugin_install.py
> >
> >
> > Do you accept the license terms for the plug-in (y=yes*, n=no, q=quit) ? y
> > sh: lsb_release: not found
> >
> > Done.
> >
> >
> > But I still cant get the printer to work!
> > The good news it that scanning works now, but if I try to print I get an error about the missing plugin.
> >
> > So here is what I did:
> >
> > - Installing hplip / hplip-gui and gtk+2-cups / gtk+3-cups
> > - doing the plugin installation shown above
> >
> > When I try to print a testpage hplip-systray says: required plugin not found!
> >
> > I did copy HP_LaserJet_MFP_M129-M134.ppd from /etc/cups/ppd/ to /usr/local/share/foomatic/db/source/PPD/HP/
> > (cause the gui setup is looking there), but no effect!
> >
> > What am I missing?
>
> Honestly, I don't know.
> Without direct access to the hardware, it's kind of hard for me to help any
> further. That specific printer maight not even be able to work on OpenBSD...
> The workaround and associated doc I made in the pkg-readme are theoretical
> because I don't have a printer that requires a plugin to be able to function
> properly. I've been told in the past that it worked (on some printers at least)
> but maybe not all?
>
> Sorry but I am afraid you are on you own on this one.
> If you find a way to make it work, please do share it and I'll add the required
> steps in the the pkg-readme.
>
> Thanks...
>
> > 15.06.2017, 09:41, "Antoine Jacoutot" <ajacoutot@bsdfrog.org>:
> > > On Sun, Jun 04, 2017 at 07:09:19PM +0200, Reheis Claus wrote:
> > >> Hi all,
> > >>
> > >> Recently I acquired an HP Laserjet Pro MFP M130fn and I would like to
> > >> use it with my OpenBSD Deskop...
> > >> As it is supported since hplip 3.17 I have to use OpenBSD Current.
> > >> I managed to get until the plugin installation, but now I am stuck at
> > >> the point:
> > >>
> > >> /usr/local/bin/python2.7 plugin_install.py
> > >>
> > >> License blablabla
> > >>
> > >> Do you accept the license terms for the plug-in (y=yes*, n=no, q=quit) ? y
> > >> sh: lsb_release: not found
> > >> Plugin installation failed
> > >> error: Plugin installation failed
> > >>
> > >> Any advice? thx
> > >
> > > Hi.
> > >
> > > Thanks for the report.
> > > FWIW I just fixed it in current.
> > >
> > > --
> > > Antoine
> >
>
> --
> Antoine
I am running BSD 6.4, just installed
I have similar issues with an HP M1132 MFP. What plugin are you talking
about here? I can find nothing in the packages. However I do find one on
the FreeBSD package site.
I cannot get the hplip-setup to run - either it does not recognise the
GUI (but demands one) or:
# hplip-setup -i 192.168.0.10
(I select 1 for printer on wifi)
error: no device selected/specified that supports this functionality
So where do I go from here?
(the real solution is to junk this printer and buy a proper postscript
one but can't afford that right now).
best
Ian
No comments:
Post a Comment