Vertigo Altair <vertigo.altair@gmail.com> writes:
Hello,
I had a Dell XPS 8100 with a similar problem and I was able to get
around it by disabling ACPI at the boot prompt. Of course, we have very
different machines, but it's worth a shot. Unfortunately the boot was
extremely slow, on the order of 10min with acpi reenabled, and several minutes
without it. Hopefully someone more knowledgeable than me will give a
more reasoned answer. Good luck.
Best,
Andrea
> Hi,
> I have a Dell VEP 1445 Whitebox, I want to install OpenBSD 6.6. on it. But
> When I try to boot, the boot process is stucking. There is no output after
> " erase ^?, werase"
>
> BIOS Boot Selector for VEP1400-X
> Version 3.48.0.9-4
>
>
> POST Configuration
> CPU Signature 506F1
> CPU FamilyID=6, Model=5F, SteppingId=1, Processor=0
> Microcode Revision 2E
> Platform ID: 0x0
> PMG_CST_CFG_CTL: 0x37
> Misc EN: 0x840089
> Gen PM ConA: 0xA0A00200
> Therm Status: 0x8000000
> POST Control=0xEA000F03, Status=0xE600DF00
>
> BIOS initializations...
>
> CPGC Memtest Channel 0 ...................... PASS
>
> POST:
> RTC Battery OK at last cold boot
> RTC date 5/3/2020 9:24:11
>
> POST SPD test ............................... PASS
>
> POST Lower DRAM Memory test .........
> POST ECC Test ............................... PASS
>
> .... Perf cnt (curr,fixed): 0x32AFD1520,0x8B637FB20
>
> POST Lower DRAM Memory test ................. PASS
> POST Lower DRAM ECC check ................... PASS
>
> Current BOOT from Primary BIOS
> DxE POST
>
> POST Upper DRAM Memory test
> Short memory cell test
>
> POST Upper DRAM Memory test ................. PASS
> HDD Access .................................. PASS
> USB device detected
> Temperature test ............................ PASS
> FAN controller test ......................... PASS
> EEPROM test ................................. PASS
> POST PCI test ............................... PASS
> POST BMC Interface test ..................... PASS
> POST NVRAM check ............................ PASS
> POST overall test results ................... PASS
>
> NVRAM: 00 DF 00 E6 03 0F 00 EA 01 55 3E __ 00 0F 00 F7
> Version 2.19.1266. Copyright (C) 2019 American Megatrends, Inc.
> BIOS Date: 06/26/2019 22:19:26 Ver: 0ACHI040
> Press <DEL> or <F2> to enter setup.
> probing: pc0 com1 com2 com3 mem[640K 1894M 117M 972K 4M 14336M]
> disk: hd0 hd1* hd2*
>>> OpenBSD/amd64 BOOTX64 3.46
> boot> stty com0 115200
> boot> set tty com0
> switching console to com0
>>> OpenBSD/amd64 BOOTX64 3.46
> boot>
> cannot open hd0a:/etc/random.seed: No such file or directory
> booting hd0a:/6.6/amd64/bsd.rd: 3732171+1537024+3885432+0+598016
> [376562+128+455544+303577]=0xa648d0
> entry point at 0x1001000
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California. All rights reserved.
> Copyright (c) 1995-2019 OpenBSD. All rights reserved.
> https://www.OpenBSD.org <https://www.openbsd.org/>
>
> OpenBSD 6.6 (RAMDISK_CD) #349: Sat Oct 12 11:03:52 MDT 2019
> deraadt@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/RAMDISK_CD
> real mem = 17131601920 (16337MB)
> avail mem = 16608419840 (15839MB)
> mainbus0 at root
> bios0 at mainbus0: SMBIOS rev. 3.0 @ 0x7f1ef000 (55 entries)
> bios0: vendor American Megatrends Inc. version "3.48.0.9-4" date 06/26/2019
> bios0: Dell EMC VEP1445-V220
> acpi0 at bios0: ACPI 6.1
> acpi0: tables DSDT FACP FPDT FIDT MCFG APIC BDAT HPET UEFI SSDT DMAR SPCR
> TPM2 HEST BERT ERST EINJ WSMT
> acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> cpu0 at mainbus0: apid 0 (boot processor)
> cpu0: Intel(R) Atom(TM) CPU C3758 @ 2.20GHz, 2200.40 MHz, 06-5f-01
> cpu0:
> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SMEP,ERMS,MPX,RDSEED,SMAP,CLFLUSHOPT,PT,SHA,MD_CLEAR,IBRS,IBPB,STIBP,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES
> cpu0: 2MB 64b/line 16-way L2 cache
> cpu0: apic clock running at 25MHz
> cpu0: mwait min=64, max=64, C-substates=0.2.0.2, IBE
> cpu at mainbus0: not configured
> cpu at mainbus0: not configured
> cpu at mainbus0: not configured
> cpu at mainbus0: not configured
> cpu at mainbus0: not configured
> cpu at mainbus0: not configured
> cpu at mainbus0: not configured
> ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
> acpiprt0 at acpi0: bus 0 (PCI0)
> acpiprt1 at acpi0: bus -1 (PEX0)
> acpiprt2 at acpi0: bus -1 (PEX1)
> acpiprt3 at acpi0: bus 2 (PEX2)
> acpiprt4 at acpi0: bus -1 (PEX3)
> acpiprt5 at acpi0: bus -1 (PEX4)
> acpiprt6 at acpi0: bus 4 (PEX5)
> acpiprt7 at acpi0: bus -1 (PEX6)
> acpiprt8 at acpi0: bus -1 (PEX7)
> acpiprt9 at acpi0: bus 1 (VRP2)
> acpiprt10 at acpi0: bus 5 (VRP0)
> acpiprt11 at acpi0: bus 7 (VRP1)
> acpicpu at acpi0 not configured
> acpitz at acpi0 not configured
> "PNP0A08" at acpi0 not configured
> "PNP0003" at acpi0 not configured
> acpicmos0 at acpi0
> "MVS6190" at acpi0 not configured
> "PICB000" at acpi0 not configured
> "INTC3000" at acpi0 not configured
> "PNP0C33" at acpi0 not configured
> "MSFT0101" at acpi0 not configured
> pci0 at mainbus0 bus 0
> 0:31:5: mem address conflict 0xfe010000/0x1000
> pchb0 at pci0 dev 0 function 0 "Intel C3000 Host" rev 0x11
> pchb1 at pci0 dev 4 function 0 "Intel C3000 GLREG" rev 0x11
> "Intel C3000 RCEC" rev 0x11 at pci0 dev 5 function 0 not configured
> ppb0 at pci0 dev 6 function 0 "Intel C3000 PCIE" rev 0x11
> pci1 at ppb0 bus 1
> "Intel C3000 QAT" rev 0x11 at pci1 dev 0 function 0 not configured
> ppb1 at pci0 dev 11 function 0 "Intel C3000 PCIE" rev 0x11
> pci2 at ppb1 bus 2
> em0 at pci2 dev 0 function 0 "Intel I350" rev 0x01: msi, address
> 50:9a:4c:ea:96:70
> em1 at pci2 dev 0 function 1 "Intel I350" rev 0x01: msi, address
> 50:9a:4c:ea:96:71
> em2 at pci2 dev 0 function 2 "Intel I350" rev 0x01: msi, address
> 50:9a:4c:ea:96:72
> em3 at pci2 dev 0 function 3 "Intel I350" rev 0x01: msi, address
> 50:9a:4c:ea:96:73
> ppb2 at pci0 dev 15 function 0 "Intel C3000 PCIE" rev 0x11
> pci3 at ppb2 bus 4
> vendor "Atheros", unknown product 0x003c (class network subclass
> miscellaneous, rev 0x00) at pci3 dev 0 function 0 not configured
> "Intel C3000 SMBus" rev 0x11 at pci0 dev 18 function 0 not configured
> ahci0 at pci0 dev 19 function 0 "Intel C3000 AHCI" rev 0x11: msi, AHCI 1.3.1
> ahci0: port 5: 6.0Gb/s
> scsibus0 at ahci0: 32 targets
> sd0 at scsibus0 targ 5 lun 0: <ATA, 256GB SATA Flash, SFDN>
> naa.6611602cbad0d0d0
> sd0: 244198MB, 512 bytes/sector, 500118192 sectors, thin
> xhci0 at pci0 dev 21 function 0 "Intel C3000 xHCI" rev 0x11: msi, xHCI 1.0
> usb0 at xhci0: USB revision 3.0
> uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev
> 3.00/1.00 addr 1
> ppb3 at pci0 dev 22 function 0 "Intel C3000 PCIE" rev 0x11
> pci4 at ppb3 bus 5
> "Intel X553 SFP+" rev 0x11 at pci4 dev 0 function 0 not configured
> "Intel X553 SFP+" rev 0x11 at pci4 dev 0 function 1 not configured
> ppb4 at pci0 dev 23 function 0 "Intel C3000 PCIE" rev 0x11
> pci5 at ppb4 bus 7
> "Intel X553 SGMII" rev 0x11 at pci5 dev 0 function 0 not configured
> "Intel X553 SGMII" rev 0x11 at pci5 dev 0 function 1 not configured
> "Intel C3000 ME HECI" rev 0x11 at pci0 dev 24 function 0 not configured
> sdhc0 at pci0 dev 28 function 0 "Intel C3000 eMMC" rev 0x11: apic 2 int 16
> sdhc0: SDHC 3.0, 200 MHz base clock
> sdmmc0 at sdhc0: 8-bit, sd high-speed, mmc high-speed, dma
> "Intel C3000 LPC" rev 0x11 at pci0 dev 31 function 0 not configured
> "Intel C3000 PMC" rev 0x11 at pci0 dev 31 function 2 not configured
> "Intel C3000 SMBus" rev 0x11 at pci0 dev 31 function 4 not configured
> "Intel C3000 SPI" rev 0x11 at pci0 dev 31 function 5 not configured
> isa0 at mainbus0
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> com0: console
> com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
> com2 at isa0 port 0x3e8/8 irq 5: ns16550a, 16 byte fifo
> efifb at mainbus0 not configured
> umass0 at uhub0 port 1 configuration 1 interface 0 "SanDisk' Cruzer Fit"
> rev 2.00/1.00 addr 2
> umass0: using SCSI over Bulk-Only
> scsibus1 at umass0: 2 targets, initiator 0
> sd1 at scsibus1 targ 1 lun 0: <SanDisk', Cruzer Fit, 1.00> removable
> serial.07815571221118104030
> sd1: 14664MB, 512 bytes/sector, 30031872 sectors
> sdmmc0: can't enable card
> softraid0 at root
> scsibus2 at softraid0: 256 targets
> root on rd0a swap on rd0b dump on rd0b
> erase ^?, werase
No comments:
Post a Comment