Hello Again,
I have already disabled ACPI at the boot prompt, but the result didn't
change.Thanks for suggestion..
Andrea Fleckenstein <afleck@mailbox.org>, 3 May 2020 Paz, 16:41 tarihinde
şunu yazdı:
> Vertigo Altair <vertigo.altair@gmail.com> writes:
>
> Hello,
>
> I had a Dell XPS 8100 with a similar problem and I was able to get
> around it by disabling ACPI at the boot prompt. Of course, we have very
> different machines, but it's worth a shot. Unfortunately the boot was
> extremely slow, on the order of 10min with acpi reenabled, and several
> minutes
> without it. Hopefully someone more knowledgeable than me will give a
> more reasoned answer. Good luck.
>
> Best,
> Andrea
>
> > Hi,
> > I have a Dell VEP 1445 Whitebox, I want to install OpenBSD 6.6. on it.
> But
> > When I try to boot, the boot process is stucking. There is no output
> after
> > " erase ^?, werase"
> >
> > BIOS Boot Selector for VEP1400-X
> > Version 3.48.0.9-4
> >
> >
> > POST Configuration
> > CPU Signature 506F1
> > CPU FamilyID=6, Model=5F, SteppingId=1, Processor=0
> > Microcode Revision 2E
> > Platform ID: 0x0
> > PMG_CST_CFG_CTL: 0x37
> > Misc EN: 0x840089
> > Gen PM ConA: 0xA0A00200
> > Therm Status: 0x8000000
> > POST Control=0xEA000F03, Status=0xE600DF00
> >
> > BIOS initializations...
> >
> > CPGC Memtest Channel 0 ...................... PASS
> >
> > POST:
> > RTC Battery OK at last cold boot
> > RTC date 5/3/2020 9:24:11
> >
> > POST SPD test ............................... PASS
> >
> > POST Lower DRAM Memory test .........
> > POST ECC Test ............................... PASS
> >
> > .... Perf cnt (curr,fixed): 0x32AFD1520,0x8B637FB20
> >
> > POST Lower DRAM Memory test ................. PASS
> > POST Lower DRAM ECC check ................... PASS
> >
> > Current BOOT from Primary BIOS
> > DxE POST
> >
> > POST Upper DRAM Memory test
> > Short memory cell test
> >
> > POST Upper DRAM Memory test ................. PASS
> > HDD Access .................................. PASS
> > USB device detected
> > Temperature test ............................ PASS
> > FAN controller test ......................... PASS
> > EEPROM test ................................. PASS
> > POST PCI test ............................... PASS
> > POST BMC Interface test ..................... PASS
> > POST NVRAM check ............................ PASS
> > POST overall test results ................... PASS
> >
> > NVRAM: 00 DF 00 E6 03 0F 00 EA 01 55 3E __ 00 0F 00 F7
> > Version 2.19.1266. Copyright (C) 2019 American Megatrends, Inc.
> > BIOS Date: 06/26/2019 22:19:26 Ver: 0ACHI040
> > Press <DEL> or <F2> to enter setup.
> > probing: pc0 com1 com2 com3 mem[640K 1894M 117M 972K 4M 14336M]
> > disk: hd0 hd1* hd2*
> >>> OpenBSD/amd64 BOOTX64 3.46
> > boot> stty com0 115200
> > boot> set tty com0
> > switching console to com0
> >>> OpenBSD/amd64 BOOTX64 3.46
> > boot>
> > cannot open hd0a:/etc/random.seed: No such file or directory
> > booting hd0a:/6.6/amd64/bsd.rd: 3732171+1537024+3885432+0+598016
> > [376562+128+455544+303577]=0xa648d0
> > entry point at 0x1001000
> > Copyright (c) 1982, 1986, 1989, 1991, 1993
> > The Regents of the University of California. All rights
> reserved.
> > Copyright (c) 1995-2019 OpenBSD. All rights reserved.
> > https://www.OpenBSD.org <https://www.openbsd.org/>
> >
> > OpenBSD 6.6 (RAMDISK_CD) #349: Sat Oct 12 11:03:52 MDT 2019
> > deraadt@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/RAMDISK_CD
> > real mem = 17131601920 (16337MB)
> > avail mem = 16608419840 (15839MB)
> > mainbus0 at root
> > bios0 at mainbus0: SMBIOS rev. 3.0 @ 0x7f1ef000 (55 entries)
> > bios0: vendor American Megatrends Inc. version "3.48.0.9-4" date
> 06/26/2019
> > bios0: Dell EMC VEP1445-V220
> > acpi0 at bios0: ACPI 6.1
> > acpi0: tables DSDT FACP FPDT FIDT MCFG APIC BDAT HPET UEFI SSDT DMAR SPCR
> > TPM2 HEST BERT ERST EINJ WSMT
> > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> > cpu0 at mainbus0: apid 0 (boot processor)
> > cpu0: Intel(R) Atom(TM) CPU C3758 @ 2.20GHz, 2200.40 MHz, 06-5f-01
> > cpu0:
> >
> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SMEP,ERMS,MPX,RDSEED,SMAP,CLFLUSHOPT,PT,SHA,MD_CLEAR,IBRS,IBPB,STIBP,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES
> > cpu0: 2MB 64b/line 16-way L2 cache
> > cpu0: apic clock running at 25MHz
> > cpu0: mwait min=64, max=64, C-substates=0.2.0.2, IBE
> > cpu at mainbus0: not configured
> > cpu at mainbus0: not configured
> > cpu at mainbus0: not configured
> > cpu at mainbus0: not configured
> > cpu at mainbus0: not configured
> > cpu at mainbus0: not configured
> > cpu at mainbus0: not configured
> > ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
> > acpiprt0 at acpi0: bus 0 (PCI0)
> > acpiprt1 at acpi0: bus -1 (PEX0)
> > acpiprt2 at acpi0: bus -1 (PEX1)
> > acpiprt3 at acpi0: bus 2 (PEX2)
> > acpiprt4 at acpi0: bus -1 (PEX3)
> > acpiprt5 at acpi0: bus -1 (PEX4)
> > acpiprt6 at acpi0: bus 4 (PEX5)
> > acpiprt7 at acpi0: bus -1 (PEX6)
> > acpiprt8 at acpi0: bus -1 (PEX7)
> > acpiprt9 at acpi0: bus 1 (VRP2)
> > acpiprt10 at acpi0: bus 5 (VRP0)
> > acpiprt11 at acpi0: bus 7 (VRP1)
> > acpicpu at acpi0 not configured
> > acpitz at acpi0 not configured
> > "PNP0A08" at acpi0 not configured
> > "PNP0003" at acpi0 not configured
> > acpicmos0 at acpi0
> > "MVS6190" at acpi0 not configured
> > "PICB000" at acpi0 not configured
> > "INTC3000" at acpi0 not configured
> > "PNP0C33" at acpi0 not configured
> > "MSFT0101" at acpi0 not configured
> > pci0 at mainbus0 bus 0
> > 0:31:5: mem address conflict 0xfe010000/0x1000
> > pchb0 at pci0 dev 0 function 0 "Intel C3000 Host" rev 0x11
> > pchb1 at pci0 dev 4 function 0 "Intel C3000 GLREG" rev 0x11
> > "Intel C3000 RCEC" rev 0x11 at pci0 dev 5 function 0 not configured
> > ppb0 at pci0 dev 6 function 0 "Intel C3000 PCIE" rev 0x11
> > pci1 at ppb0 bus 1
> > "Intel C3000 QAT" rev 0x11 at pci1 dev 0 function 0 not configured
> > ppb1 at pci0 dev 11 function 0 "Intel C3000 PCIE" rev 0x11
> > pci2 at ppb1 bus 2
> > em0 at pci2 dev 0 function 0 "Intel I350" rev 0x01: msi, address
> > 50:9a:4c:ea:96:70
> > em1 at pci2 dev 0 function 1 "Intel I350" rev 0x01: msi, address
> > 50:9a:4c:ea:96:71
> > em2 at pci2 dev 0 function 2 "Intel I350" rev 0x01: msi, address
> > 50:9a:4c:ea:96:72
> > em3 at pci2 dev 0 function 3 "Intel I350" rev 0x01: msi, address
> > 50:9a:4c:ea:96:73
> > ppb2 at pci0 dev 15 function 0 "Intel C3000 PCIE" rev 0x11
> > pci3 at ppb2 bus 4
> > vendor "Atheros", unknown product 0x003c (class network subclass
> > miscellaneous, rev 0x00) at pci3 dev 0 function 0 not configured
> > "Intel C3000 SMBus" rev 0x11 at pci0 dev 18 function 0 not configured
> > ahci0 at pci0 dev 19 function 0 "Intel C3000 AHCI" rev 0x11: msi, AHCI
> 1.3.1
> > ahci0: port 5: 6.0Gb/s
> > scsibus0 at ahci0: 32 targets
> > sd0 at scsibus0 targ 5 lun 0: <ATA, 256GB SATA Flash, SFDN>
> > naa.6611602cbad0d0d0
> > sd0: 244198MB, 512 bytes/sector, 500118192 sectors, thin
> > xhci0 at pci0 dev 21 function 0 "Intel C3000 xHCI" rev 0x11: msi, xHCI
> 1.0
> > usb0 at xhci0: USB revision 3.0
> > uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev
> > 3.00/1.00 addr 1
> > ppb3 at pci0 dev 22 function 0 "Intel C3000 PCIE" rev 0x11
> > pci4 at ppb3 bus 5
> > "Intel X553 SFP+" rev 0x11 at pci4 dev 0 function 0 not configured
> > "Intel X553 SFP+" rev 0x11 at pci4 dev 0 function 1 not configured
> > ppb4 at pci0 dev 23 function 0 "Intel C3000 PCIE" rev 0x11
> > pci5 at ppb4 bus 7
> > "Intel X553 SGMII" rev 0x11 at pci5 dev 0 function 0 not configured
> > "Intel X553 SGMII" rev 0x11 at pci5 dev 0 function 1 not configured
> > "Intel C3000 ME HECI" rev 0x11 at pci0 dev 24 function 0 not configured
> > sdhc0 at pci0 dev 28 function 0 "Intel C3000 eMMC" rev 0x11: apic 2 int
> 16
> > sdhc0: SDHC 3.0, 200 MHz base clock
> > sdmmc0 at sdhc0: 8-bit, sd high-speed, mmc high-speed, dma
> > "Intel C3000 LPC" rev 0x11 at pci0 dev 31 function 0 not configured
> > "Intel C3000 PMC" rev 0x11 at pci0 dev 31 function 2 not configured
> > "Intel C3000 SMBus" rev 0x11 at pci0 dev 31 function 4 not configured
> > "Intel C3000 SPI" rev 0x11 at pci0 dev 31 function 5 not configured
> > isa0 at mainbus0
> > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> > com0: console
> > com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
> > com2 at isa0 port 0x3e8/8 irq 5: ns16550a, 16 byte fifo
> > efifb at mainbus0 not configured
> > umass0 at uhub0 port 1 configuration 1 interface 0 "SanDisk' Cruzer Fit"
> > rev 2.00/1.00 addr 2
> > umass0: using SCSI over Bulk-Only
> > scsibus1 at umass0: 2 targets, initiator 0
> > sd1 at scsibus1 targ 1 lun 0: <SanDisk', Cruzer Fit, 1.00> removable
> > serial.07815571221118104030
> > sd1: 14664MB, 512 bytes/sector, 30031872 sectors
> > sdmmc0: can't enable card
> > softraid0 at root
> > scsibus2 at softraid0: 256 targets
> > root on rd0a swap on rd0b dump on rd0b
> > erase ^?, werase
>
No comments:
Post a Comment