In Addition,
I rebooted the device after installation. Now, I cannot give any input from
console. I cannot even enter the bios.
Vertigo Altair <vertigo.altair@gmail.com>, 4 May 2020 Pzt, 16:15 tarihinde
şunu yazdı:
> Hello,
> I cannot change IRQ in Bios,
> In BIOS, com0 settings are like this;
> IO = 3F8h (correct) , IRQ = 7 (incorrect)
> For installation, I set com0's IRQ to 7 at UKC. And I completed
> installation successfully. However, when I try to boot after installation
> the console is stucking again. There are 16 character on the last line and
> com0 are using to IRQ = 4. At this point, I cannot reach the UKC with "boot
> -c". How can I overcome this?
>
> "Intel X553 SGMII" rev 0x11 at pci10 dev 0 function 0 not configured
> "Intel X553 SGMII" rev 0x11 at pci10 dev 0 function 1 not configured
> "Intel C3000 ME HECI" rev 0x11 at pci0 dev 24 function 0 not configured
> "Intel C3000 UART" rev 0x11 at pci0 dev 26 function 0 not configured
> "Intel C3000 UART" rev 0x11 at pci0 dev 26 function 1 not configured
> "Intel C3000 UART" rev 0x11 at pci0 dev 26 function 2 not configured
> sdhc0 at pci0 dev 28 function 0 "Intel C3000 eMMC" rev 0x11: apic 2 int 16
> sdhc0: SDHC 3.0, 200 MHz base clock
> sdmmc0 at sdhc0: 8-bit, sd high-speed, mmc high-speed, dma
> pcib0 at pci0 dev 31 function 0 "Intel C3000 LPC" rev 0x11
> "Intel C3000 PMC" rev 0x11 at pci0 dev 31 function 2 not configured
> "Intel C3000 SMBus" rev 0x11 at pci0 dev 31 function 4 not configured
> "Intel C3000 SPI" rev 0x11 at pci0 dev 31 function 5 not configured
> isa0 at pcib0
> isadma0 at isa0
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> C▒▒+
> сJͅ▒▒▒▒с▒▒ɻ▒▒▒J▒Ł▒▒: ns16550a, 16 byte fifo
> pcppi0 at isa0 port 0x61
> spkr0 at pcppi0
> wbsio0 at isa0 port 0x2e/2: NCT6776F rev 0x33
> lm1 at wbsio0 port 0xa10/8: NCT6776F
> vmm0 at mainbus0: VMX/EPT
> sdmmc0: can't enable card
> vscsi0 at root
> scsibus2 at vscsi0: 256 targets
> softraid0 at root
> scsibus3 at softraid0: 256 targets
> root on sd0a (1589b7458f9250cf.a) swap on sd0b dump on sd0b
> WARNING: / was not properly unmounted
> Automatic boot i
>
> Vertigo Altair <vertigo.altair@gmail.com>, 3 May 2020 Paz, 17:29
> tarihinde şunu yazdı:
>
>> Hello Again,
>> I have already disabled ACPI at the boot prompt, but the result didn't
>> change.Thanks for suggestion..
>>
>> Andrea Fleckenstein <afleck@mailbox.org>, 3 May 2020 Paz, 16:41
>> tarihinde şunu yazdı:
>>
>>> Vertigo Altair <vertigo.altair@gmail.com> writes:
>>>
>>> Hello,
>>>
>>> I had a Dell XPS 8100 with a similar problem and I was able to get
>>> around it by disabling ACPI at the boot prompt. Of course, we have very
>>> different machines, but it's worth a shot. Unfortunately the boot was
>>> extremely slow, on the order of 10min with acpi reenabled, and several
>>> minutes
>>> without it. Hopefully someone more knowledgeable than me will give a
>>> more reasoned answer. Good luck.
>>>
>>> Best,
>>> Andrea
>>>
>>> > Hi,
>>> > I have a Dell VEP 1445 Whitebox, I want to install OpenBSD 6.6. on it.
>>> But
>>> > When I try to boot, the boot process is stucking. There is no output
>>> after
>>> > " erase ^?, werase"
>>> >
>>> > BIOS Boot Selector for VEP1400-X
>>> > Version 3.48.0.9-4
>>> >
>>> >
>>> > POST Configuration
>>> > CPU Signature 506F1
>>> > CPU FamilyID=6, Model=5F, SteppingId=1, Processor=0
>>> > Microcode Revision 2E
>>> > Platform ID: 0x0
>>> > PMG_CST_CFG_CTL: 0x37
>>> > Misc EN: 0x840089
>>> > Gen PM ConA: 0xA0A00200
>>> > Therm Status: 0x8000000
>>> > POST Control=0xEA000F03, Status=0xE600DF00
>>> >
>>> > BIOS initializations...
>>> >
>>> > CPGC Memtest Channel 0 ...................... PASS
>>> >
>>> > POST:
>>> > RTC Battery OK at last cold boot
>>> > RTC date 5/3/2020 9:24:11
>>> >
>>> > POST SPD test ............................... PASS
>>> >
>>> > POST Lower DRAM Memory test .........
>>> > POST ECC Test ............................... PASS
>>> >
>>> > .... Perf cnt (curr,fixed): 0x32AFD1520,0x8B637FB20
>>> >
>>> > POST Lower DRAM Memory test ................. PASS
>>> > POST Lower DRAM ECC check ................... PASS
>>> >
>>> > Current BOOT from Primary BIOS
>>> > DxE POST
>>> >
>>> > POST Upper DRAM Memory test
>>> > Short memory cell test
>>> >
>>> > POST Upper DRAM Memory test ................. PASS
>>> > HDD Access .................................. PASS
>>> > USB device detected
>>> > Temperature test ............................ PASS
>>> > FAN controller test ......................... PASS
>>> > EEPROM test ................................. PASS
>>> > POST PCI test ............................... PASS
>>> > POST BMC Interface test ..................... PASS
>>> > POST NVRAM check ............................ PASS
>>> > POST overall test results ................... PASS
>>> >
>>> > NVRAM: 00 DF 00 E6 03 0F 00 EA 01 55 3E __ 00 0F 00 F7
>>> > Version 2.19.1266. Copyright (C) 2019 American Megatrends, Inc.
>>> > BIOS Date: 06/26/2019 22:19:26 Ver: 0ACHI040
>>> > Press <DEL> or <F2> to enter setup.
>>> > probing: pc0 com1 com2 com3 mem[640K 1894M 117M 972K 4M 14336M]
>>> > disk: hd0 hd1* hd2*
>>> >>> OpenBSD/amd64 BOOTX64 3.46
>>> > boot> stty com0 115200
>>> > boot> set tty com0
>>> > switching console to com0
>>> >>> OpenBSD/amd64 BOOTX64 3.46
>>> > boot>
>>> > cannot open hd0a:/etc/random.seed: No such file or directory
>>> > booting hd0a:/6.6/amd64/bsd.rd: 3732171+1537024+3885432+0+598016
>>> > [376562+128+455544+303577]=0xa648d0
>>> > entry point at 0x1001000
>>> > Copyright (c) 1982, 1986, 1989, 1991, 1993
>>> > The Regents of the University of California. All rights
>>> reserved.
>>> > Copyright (c) 1995-2019 OpenBSD. All rights reserved.
>>> > https://www.OpenBSD.org <https://www.openbsd.org/>
>>> >
>>> > OpenBSD 6.6 (RAMDISK_CD) #349: Sat Oct 12 11:03:52 MDT 2019
>>> > deraadt@amd64.openbsd.org:
>>> /usr/src/sys/arch/amd64/compile/RAMDISK_CD
>>> > real mem = 17131601920 (16337MB)
>>> > avail mem = 16608419840 (15839MB)
>>> > mainbus0 at root
>>> > bios0 at mainbus0: SMBIOS rev. 3.0 @ 0x7f1ef000 (55 entries)
>>> > bios0: vendor American Megatrends Inc. version "3.48.0.9-4" date
>>> 06/26/2019
>>> > bios0: Dell EMC VEP1445-V220
>>> > acpi0 at bios0: ACPI 6.1
>>> > acpi0: tables DSDT FACP FPDT FIDT MCFG APIC BDAT HPET UEFI SSDT DMAR
>>> SPCR
>>> > TPM2 HEST BERT ERST EINJ WSMT
>>> > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
>>> > cpu0 at mainbus0: apid 0 (boot processor)
>>> > cpu0: Intel(R) Atom(TM) CPU C3758 @ 2.20GHz, 2200.40 MHz, 06-5f-01
>>> > cpu0:
>>> >
>>> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SMEP,ERMS,MPX,RDSEED,SMAP,CLFLUSHOPT,PT,SHA,MD_CLEAR,IBRS,IBPB,STIBP,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES
>>> > cpu0: 2MB 64b/line 16-way L2 cache
>>> > cpu0: apic clock running at 25MHz
>>> > cpu0: mwait min=64, max=64, C-substates=0.2.0.2, IBE
>>> > cpu at mainbus0: not configured
>>> > cpu at mainbus0: not configured
>>> > cpu at mainbus0: not configured
>>> > cpu at mainbus0: not configured
>>> > cpu at mainbus0: not configured
>>> > cpu at mainbus0: not configured
>>> > cpu at mainbus0: not configured
>>> > ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
>>> > acpiprt0 at acpi0: bus 0 (PCI0)
>>> > acpiprt1 at acpi0: bus -1 (PEX0)
>>> > acpiprt2 at acpi0: bus -1 (PEX1)
>>> > acpiprt3 at acpi0: bus 2 (PEX2)
>>> > acpiprt4 at acpi0: bus -1 (PEX3)
>>> > acpiprt5 at acpi0: bus -1 (PEX4)
>>> > acpiprt6 at acpi0: bus 4 (PEX5)
>>> > acpiprt7 at acpi0: bus -1 (PEX6)
>>> > acpiprt8 at acpi0: bus -1 (PEX7)
>>> > acpiprt9 at acpi0: bus 1 (VRP2)
>>> > acpiprt10 at acpi0: bus 5 (VRP0)
>>> > acpiprt11 at acpi0: bus 7 (VRP1)
>>> > acpicpu at acpi0 not configured
>>> > acpitz at acpi0 not configured
>>> > "PNP0A08" at acpi0 not configured
>>> > "PNP0003" at acpi0 not configured
>>> > acpicmos0 at acpi0
>>> > "MVS6190" at acpi0 not configured
>>> > "PICB000" at acpi0 not configured
>>> > "INTC3000" at acpi0 not configured
>>> > "PNP0C33" at acpi0 not configured
>>> > "MSFT0101" at acpi0 not configured
>>> > pci0 at mainbus0 bus 0
>>> > 0:31:5: mem address conflict 0xfe010000/0x1000
>>> > pchb0 at pci0 dev 0 function 0 "Intel C3000 Host" rev 0x11
>>> > pchb1 at pci0 dev 4 function 0 "Intel C3000 GLREG" rev 0x11
>>> > "Intel C3000 RCEC" rev 0x11 at pci0 dev 5 function 0 not configured
>>> > ppb0 at pci0 dev 6 function 0 "Intel C3000 PCIE" rev 0x11
>>> > pci1 at ppb0 bus 1
>>> > "Intel C3000 QAT" rev 0x11 at pci1 dev 0 function 0 not configured
>>> > ppb1 at pci0 dev 11 function 0 "Intel C3000 PCIE" rev 0x11
>>> > pci2 at ppb1 bus 2
>>> > em0 at pci2 dev 0 function 0 "Intel I350" rev 0x01: msi, address
>>> > 50:9a:4c:ea:96:70
>>> > em1 at pci2 dev 0 function 1 "Intel I350" rev 0x01: msi, address
>>> > 50:9a:4c:ea:96:71
>>> > em2 at pci2 dev 0 function 2 "Intel I350" rev 0x01: msi, address
>>> > 50:9a:4c:ea:96:72
>>> > em3 at pci2 dev 0 function 3 "Intel I350" rev 0x01: msi, address
>>> > 50:9a:4c:ea:96:73
>>> > ppb2 at pci0 dev 15 function 0 "Intel C3000 PCIE" rev 0x11
>>> > pci3 at ppb2 bus 4
>>> > vendor "Atheros", unknown product 0x003c (class network subclass
>>> > miscellaneous, rev 0x00) at pci3 dev 0 function 0 not configured
>>> > "Intel C3000 SMBus" rev 0x11 at pci0 dev 18 function 0 not configured
>>> > ahci0 at pci0 dev 19 function 0 "Intel C3000 AHCI" rev 0x11: msi, AHCI
>>> 1.3.1
>>> > ahci0: port 5: 6.0Gb/s
>>> > scsibus0 at ahci0: 32 targets
>>> > sd0 at scsibus0 targ 5 lun 0: <ATA, 256GB SATA Flash, SFDN>
>>> > naa.6611602cbad0d0d0
>>> > sd0: 244198MB, 512 bytes/sector, 500118192 sectors, thin
>>> > xhci0 at pci0 dev 21 function 0 "Intel C3000 xHCI" rev 0x11: msi, xHCI
>>> 1.0
>>> > usb0 at xhci0: USB revision 3.0
>>> > uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev
>>> > 3.00/1.00 addr 1
>>> > ppb3 at pci0 dev 22 function 0 "Intel C3000 PCIE" rev 0x11
>>> > pci4 at ppb3 bus 5
>>> > "Intel X553 SFP+" rev 0x11 at pci4 dev 0 function 0 not configured
>>> > "Intel X553 SFP+" rev 0x11 at pci4 dev 0 function 1 not configured
>>> > ppb4 at pci0 dev 23 function 0 "Intel C3000 PCIE" rev 0x11
>>> > pci5 at ppb4 bus 7
>>> > "Intel X553 SGMII" rev 0x11 at pci5 dev 0 function 0 not configured
>>> > "Intel X553 SGMII" rev 0x11 at pci5 dev 0 function 1 not configured
>>> > "Intel C3000 ME HECI" rev 0x11 at pci0 dev 24 function 0 not configured
>>> > sdhc0 at pci0 dev 28 function 0 "Intel C3000 eMMC" rev 0x11: apic 2
>>> int 16
>>> > sdhc0: SDHC 3.0, 200 MHz base clock
>>> > sdmmc0 at sdhc0: 8-bit, sd high-speed, mmc high-speed, dma
>>> > "Intel C3000 LPC" rev 0x11 at pci0 dev 31 function 0 not configured
>>> > "Intel C3000 PMC" rev 0x11 at pci0 dev 31 function 2 not configured
>>> > "Intel C3000 SMBus" rev 0x11 at pci0 dev 31 function 4 not configured
>>> > "Intel C3000 SPI" rev 0x11 at pci0 dev 31 function 5 not configured
>>> > isa0 at mainbus0
>>> > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
>>> > com0: console
>>> > com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
>>> > com2 at isa0 port 0x3e8/8 irq 5: ns16550a, 16 byte fifo
>>> > efifb at mainbus0 not configured
>>> > umass0 at uhub0 port 1 configuration 1 interface 0 "SanDisk' Cruzer
>>> Fit"
>>> > rev 2.00/1.00 addr 2
>>> > umass0: using SCSI over Bulk-Only
>>> > scsibus1 at umass0: 2 targets, initiator 0
>>> > sd1 at scsibus1 targ 1 lun 0: <SanDisk', Cruzer Fit, 1.00> removable
>>> > serial.07815571221118104030
>>> > sd1: 14664MB, 512 bytes/sector, 30031872 sectors
>>> > sdmmc0: can't enable card
>>> > softraid0 at root
>>> > scsibus2 at softraid0: 256 targets
>>> > root on rd0a swap on rd0b dump on rd0b
>>> > erase ^?, werase
>>>
>>
No comments:
Post a Comment