your PROM is likely setup to boot a "bsd" kernel in the msdos partition,
rather than the "boot" file. The "boot" file will load /bsd from the ffs
partition.
Amarendra Godbole <amarendra.godbole@gmail.com> wrote:
> So I used sysupgrade to upgrade the ERL from 6.7 to 6.8. It went through
> everything fine, downloaded the sets, extracts, etc. and reboots. However,
> it boots back into the old 6.7 kernel. I can see /bsd.upgrade created, and
> /home/_sysupgrade is empty. but did not see any option to trigger the
> upgrade. I thought it should have been automatically handled by sysupgrade.
>
> What did I miss?
>
> Thanks.
>
> -Amarendra
>
>
> erl# uname -a
> OpenBSD erl.lan 6.7 GENERIC.MP#134 octeon
>
> erl# ls -l
> total 79128
> -rw-r--r-- 1 root wheel 578 May 7 2020 .cshrc
> -rw-r--r-- 1 root wheel 468 May 7 2020 .profile
> drwxr-xr-x 2 root wheel 512 May 7 2020 altroot
> -rw-r--r-- 1 root wheel 160 Mar 31 00:08 auto_upgrade.conf
> drwxr-xr-x 2 root wheel 1024 May 7 2020 bin
> -rwx------ 1 root wheel 7626800 Mar 31 00:10 bsd
> -rwx------ 1 root wheel 7623592 Mar 31 00:01 bsd.booted
> -rw------- 1 root wheel 8843608 May 7 2020 bsd.rd
> -rw------- 1 root wheel 7568260 May 7 2020 bsd.sp
> -rwx------ 1 root wheel 8823044 Mar 31 00:09 bsd.upgrade
> drwxr-xr-x 4 root wheel 18432 Mar 31 00:10 dev
> drwxr-xr-x 23 root wheel 2048 Mar 31 00:11 etc
> drwxr-xr-x 4 root wheel 512 Oct 15 21:09 home
> drwxr-xr-x 2 root wheel 512 May 7 2020 mnt
> drwx------ 3 root wheel 512 Mar 31 01:30 root
> drwxr-xr-x 2 root wheel 1536 May 7 2020 sbin
> lrwxrwx--- 1 root wheel 11 May 7 2020 sys -> usr/src/sys
> drwxrwxrwt 6 root wheel 512 Mar 31 07:45 tmp
> drwxr-xr-x 16 root wheel 512 Sep 7 2020 usr
> drwxr-xr-x 23 root wheel 512 May 7 2020 var
> erl#
>
> erl# dmesg
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California. All rights reserved.
> Copyright (c) 1995-2020 OpenBSD. All rights reserved.
> https://www.OpenBSD.org
>
> OpenBSD 6.7 (GENERIC.MP) #134: Thu May 7 16:05:06 MDT 2020
> deraadt@octeon.openbsd.org:/usr/src/sys/arch/octeon/compile/GENERIC.MP
> real mem = 536870912 (512MB)
> avail mem = 506740736 (483MB)
> mainbus0 at root: board 20002 rev 2.18
> cpu0 at mainbus0: CN50xx CPU rev 0.1 500 MHz, Software FP emulation
> cpu0: cache L1-I 32KB 4 way D 16KB 64 way, L2 128KB 8 way
> cpu1 at mainbus0: CN50xx CPU rev 0.1 500 MHz, Software FP emulation
> cpu1: cache L1-I 32KB 4 way D 16KB 64 way, L2 128KB 8 way
> clock0 at mainbus0: int 5
> octcrypto0 at mainbus0
> iobus0 at mainbus0
> simplebus0 at iobus0: "soc"
> octciu0 at simplebus0
> octsmi0 at simplebus0
> octpip0 at simplebus0
> octgmx0 at octpip0 interface 0
> cnmac0 at octgmx0: RGMII, address 78:8a:20:46:a8:c0
> atphy0 at cnmac0 phy 7: AR8035 10/100/1000 PHY, rev. 2
> cnmac1 at octgmx0: RGMII, address 78:8a:20:46:a8:c1
> atphy1 at cnmac1 phy 6: AR8035 10/100/1000 PHY, rev. 2
> cnmac2 at octgmx0: RGMII, address 78:8a:20:46:a8:c2
> atphy2 at cnmac2 phy 5: AR8035 10/100/1000 PHY, rev. 2
> com0 at simplebus0: ns16550a, 64 byte fifo
> com0: console
> dwctwo0 at iobus0 base 0x1180068000000 irq 56
> usb0 at dwctwo0: USB revision 2.0
> uhub0 at usb0 configuration 1 interface 0 "Octeon DWC2 root hub" rev
> 2.00/1.00 addr 1
> octrng0 at iobus0 base 0x1400000000000 irq 0
> /dev/ksyms: Symbol table not valid.
> umass0 at uhub0 port 1 configuration 1 interface 0 "Lexar USB Flash Drive"
> rev 2.10/11.00 addr 2
> umass0: using SCSI over Bulk-Only
> scsibus0 at umass0: 2 targets, initiator 0
> sd0 at scsibus0 targ 1 lun 0: <Lexar, USB Flash Drive, 1100> removable
> serial.21c40cd1719080003000
> sd0: 30526MB, 512 bytes/sector, 62517248 sectors
> vscsi0 at root
> scsibus1 at vscsi0: 256 targets
> softraid0 at root
> scsibus2 at softraid0: 256 targets
> boot device: sd0
> root on sd0a (2124441bc835a462.a) swap on sd0b dump on sd0b
> WARNING: No TOD clock, believing file system.
> WARNING: CHECK AND RESET THE DATE!
No comments:
Post a Comment