Re: Bwfm problems

Hello,

I decided to just to symlink the raspberry pi 4 configuration for the
driver, to the filename expected by the bwfm driver, and it loads just
fine now, I have attached the dmesg below:

OpenBSD 7.2 (GENERIC.MP) #5: Wed Jan 11 01:01:10 MST 2023

root@syspatch-72-arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/GENERIC.MP
real mem = 3132207104 (2987MB)
avail mem = 3001634816 (2862MB)
random: good seed from bootblocks
mainbus0 at root: ACPI
psci0 at mainbus0: PSCI 1.1, SMCCC 1.2
cpu0 at mainbus0 mpidr 0: ARM Cortex-A72 r0p3
cpu0: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
cpu0: 1024KB 64b/line 16-way L2 cache
cpu0: CRC32,ASID16
cpu1 at mainbus0 mpidr 1: ARM Cortex-A72 r0p3
cpu1: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
cpu1: 1024KB 64b/line 16-way L2 cache
cpu1: CRC32,ASID16
cpu2 at mainbus0 mpidr 2: ARM Cortex-A72 r0p3
cpu2: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
cpu2: 1024KB 64b/line 16-way L2 cache
cpu2: CRC32,ASID16
cpu3 at mainbus0 mpidr 3: ARM Cortex-A72 r0p3
cpu3: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
cpu3: 1024KB 64b/line 16-way L2 cache
cpu3: CRC32,ASID16
efi0 at mainbus0: UEFI 2.7
efi0: https://github.com/pftf/RPi4 rev 0x10000
smbios0 at efi0: SMBIOS 3.3.0
smbios0: vendor https://github.com/pftf/RPi4 version "UEFI Firmware
v1.33" date 03/07/2022
smbios0: Raspberry Pi Foundation Raspberry Pi 4 Model B
apm0 at mainbus0
ampintc0 at mainbus0 nirq 256, ncpu 4 ipi: 0, 1, 2: "interrupt-controller"
agtimer0 at mainbus0: 54000 kHz
acpi0 at mainbus0: ACPI 6.3
acpi0: sleep states
acpi0: tables DSDT FACP CSRT DBG2 GTDT APIC PPTT SPCR SSDT SSDT
acpi0: wakeup devices
"BCM2849" at acpi0 not configured
"BCM2835" at acpi0 not configured
"BCM2854" at acpi0 not configured
"ACPI0007" at acpi0 not configured
"ACPI0007" at acpi0 not configured
"ACPI0007" at acpi0 not configured
"ACPI0007" at acpi0 not configured
"ACPI0004" at acpi0 not configured
"BCM2848" at acpi0 not configured
"BCM2850" at acpi0 not configured
"BCM2856" at acpi0 not configured
"BCM2845" at acpi0 not configured
"BCM2841" at acpi0 not configured
"BCM2841" at acpi0 not configured
"BCM2838" at acpi0 not configured
"BCM2839" at acpi0 not configured
"BCM2844" at acpi0 not configured
pluart0 at acpi0 URT0 addr 0xfe201000/0x1000 irq 153
pluart0: console
"BCM2836" at acpi0 not configured
"BCM2EA6" at acpi0 not configured
"MSFT8000" at acpi0 not configured
sdhc0 at acpi0 SDC1 addr 0xfe300000/0x100 irq 158
sdhc0: SDHC 3.0, 250 MHz base clock
sdmmc0 at sdhc0: 4-bit, sd high-speed, mmc high-speed
bse0 at acpi0 ETH0 addr 0xfd580000/0x10000 irq 189: address
dc:a6:32:78:eb:b1
brgphy0 at bse0 phy 1: BCM54210E 10/100/1000baseT PHY, rev. 2
"PNP0C06" at acpi0 not configured
"ACPI0004" at acpi0 not configured
sdhc1 at acpi0 SDC3 addr 0xfe340000/0x100 irq 158
sdhc1: SDHC 3.0, 100 MHz base clock
sdmmc1 at sdhc1: 8-bit, sd high-speed, mmc high-speed
"ACPI0004" at acpi0 not configured
xhci0 at acpi0 XHC0 addr 0x600000000/0x1000 irq 175, xHCI 1.0
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 configuration 1 interface 0 "Generic xHCI root hub" rev
3.00/1.00 addr 1
acpitz0 at acpi0: critical temperature is 90 degC
scsibus0 at sdmmc1: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SB32G, 0080> removable
sd0: 30436MB, 512 bytes/sector, 62333952 sectors
bwfm0 at sdmmc0 function 1
manufacturer 0x02d0, product 0xa9a6 at sdmmc0 function 2 not configured
manufacturer 0x02d0, product 0xa9a6 at sdmmc0 function 3 not configured
uhub1 at uhub0 port 1 configuration 1 interface 0 "VIA Labs USB2.0 Hub"
rev 2.10/4.21 addr 2
umass0 at uhub1 port 4 configuration 1 interface 0 "JMicron JMS579" rev
2.10/2.04 addr 3
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <sobetter, EXT, 0204>
serial.152d0578781113065958
sd1: 238475MB, 512 bytes/sector, 488397168 sectors
axen0 at uhub0 port 3 configuration 1 interface 0 "ASIX Elec. Corp.
AX88179" rev 3.00/1.00 addr 4
axen0: AX88179, address 7c:c2:c6:44:18:53
rgephy0 at axen0 phy 3: RTL8169S/8110S/8211 PHY, rev. 5
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
root on sd1a (92f440dc01ea6e2f.a) swap on sd1b dump on sd1b
WARNING: clock lost 330 days
WARNING: CHECK AND RESET THE DATE!
bwfm0: address dc:a6:32:78:eb:b2
pppoe0: received unexpected PADO

The issue is, the hostap still does not work, it says its active and
hostap has showed up under media, so the driver has detected that it is
supported, and there is no errors, yet when I scan for wifi connections
to connect to, it does not show up:

bwfm0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr dc:a6:32:78:eb:b2
index 4 priority 4 llprio 3
groups: wlan
media: IEEE802.11 autoselect hostap (autoselect mode 11n hostap)
status: active
ieee80211: nwid PolarianWifi chan 9 bssid dc:a6:32:78:eb:b2
wpakey wpaprotos wpa2 wpaakms psk wpaciphers ccmp wpagroupcipher ccmp
inet 192.168.3.1 netmask 0xffffff00 broadcast 192.168.3.255

I just noticed it has autoselected 11n, the chipset is meant to be ac,
so I assume this could be a possible problem...

See my hostname.bwfm0 configuration below:

inet 192.168.3.1 255.255.255.0
mediaopt hostap
nwid PolarianWifi wpakey <my password> chan 9

I have put <my password> in to hide my actual password, before anyone
comments that is the issue :P

Any suggestions would be useful :)
--
Polarian
GPG signature: 0770E5312238C760
Website: https://polarian.dev
JID/XMPP: polarian@polarian.dev