On Apr 25 13:12:46, void@f-m.fm wrote: > Here is output from the uboot process. It never gets to the part where > it's handed over to openbsd. Note that this is after installation from sdmmc > the sdmmc card removed and the machine turned on with the usb3 ssd plugged in. Is that the same usb port you used during installation? Have you tried booting with the usb disk in other usb ports? > 1.67 RPi: BOOTSYS release VERSION:85353ce4 DATE: 2026/02/23 TIME: 10:01:39 > 1.67 BOOTMODE: 0x06 partition 0 build-ts BUILD_TIMESTAMP=1771840899 serial 1af94b12 boardrev e04171 stc 1675632 > 1.68 AON_RESET: 00000003 PM_RSTS 00001000 > 1.68 POWER_OFF_ON_HALT: 0 WAIT_FOR_POWER_BUTTON 0 power-on-reset 1 > 1.69 RP1_BOOT chip ID: 0x20001927 > 1.70 PCIEx1: PWR 0 DET_WAKE 0 > 1.70 part 00000000 reset_info 00000000 > 1.70 PMIC reset-event 00000000 rtc 00000001 alarm 00000000 enabled 0 > 1.71 uSD voltage 3.3V > 1.71 SDRAM_CONFIG: 1b > 1.71 Initialising SDRAM rank 2 total-size: 128Gbit 0 part: 0 (0x1b 0x1b) > 1.72 memsys_init: 0 128Gbit MCB 0x80015ff0: 5488 > 1.73 DDR 4267 Mbps dual-rank:1 byte-mode:1 size-gbit:128 > 2.37 RP1 FW: load 0 > 2.38 RP1_BOOT chip ID: 0x20001927 > 3.53 RP1 FW: load 1 > 3.96 OTP boardrev e04171 bootrom a a > 3.96 Customer key hash 0000000000000000000000000000000000000000000000000000000000000000 > 3.97 VC-JTAG unlocked > 3.99 RP1_BOOT chip ID: 0x20001927 > > 4.63 PCI2 init > 4.65 PCI2 reset > 4.70 PCIe scan 00001de4:00000001 > 4.70 RP1_CHIP_INFO 20001927 > > 4.70 RPi: BOOTLOADER release VERSION:85353ce4 DATE: 2026/02/23 TIME: 10:01:39 > 4.71 BOOTMODE: 0x06 partition 0 build-ts BUILD_TIMESTAMP=1771840899 serial 1af94b12 boardrev e04171 stc 4711873 > 4.72 PCIEx1: PWR 0 DET_WAKE 0 > 4.24 M.2 PCIe HAT not detected. > 4.73 usb_pd_init status 3 > 4.73 USB_PD CONFIG 0 41 > 4.80 XHCI-STOP > 4.80 xHC0 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d > 4.80 USBSTS 1 > 4.81 xHC0 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d > 4.81 xHC0 ports 3 slots 64 intrs 4 > 4.83 XHCI-STOP > 4.83 xHC1 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d > 4.84 USBSTS 1 > 4.84 xHC1 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d > 4.84 xHC1 ports 3 slots 64 intrs 4 > 4.85 USB-PD: src-cap PDO object1 0x0a0191f4 > 4.85 Current 5000 mA > 4.85 Voltage 5000 mV > 4.86 USB-PD: src-cap PDO object2 0x0002d12c > 4.86 Current 3000 mA > 4.86 Voltage 9000 mV > 4.86 USB-PD: src-cap PDO object3 0x0003c0e1 > 4.87 Current 2250 mA > 4.87 Voltage 12000 mV > 4.87 USB-PD: src-cap PDO object4 0x0004b0b4 > 4.88 Current 1800 mA > 4.88 Voltage 15000 mV > 4.92 SD_OC: 0 > 4.25 Boot mode: USB-MSD (04) order f1 > 5.63 USB2[2] 00020ae1 connected > 5.13 USB2[2] 00200a03 connected enabled > 5.14 USB2 root HUB port 2 init > 5.27 DEV [01:00] 1.16 000000:02 class 0 VID 1a2c PID 4b61 > 5.90 HID [01:00] 1.16 000000:02 register HID > 5.53 USB3[3] 00021203 connected enabled > 5.54 USB3 root HUB port 3 init good > 5.55 DEV [02:00] 3.32 000000:03 class 0 VID 0951 PID 1780 > 5.56 MSD device [02:00] 3.32 000000:03 conf 0 iface 0 ep 82#1024 01#1024 > 5.69 MSD [02:00] 3.32 000000:03 register MSD > 9.57 XHCI-STOP > 9.57 xHC0 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d > 9.57 USBSTS 0 > 9.58 XHCI-STOP > 9.58 xHC1 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d > 9.58 USBSTS 18 > 9.59 XHCI-STOP > 9.59 xHC0 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d > 9.59 USBSTS 1 > 9.60 xHC0 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d > 9.60 xHC0 ports 3 slots 64 intrs 4 > 9.61 XHCI-STOP > 9.61 xHC1 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d > 9.62 USBSTS 19 > 9.62 xHC1 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d > 9.62 xHC1 ports 3 slots 64 intrs 4 > 9.87 USB2[2] 00020ae1 connected > 9.38 USB2[2] 00200a03 connected enabled > 9.38 USB2 root HUB port 2 init > 9.41 USB3[3] 002a1203 connected enabled > 9.76 DEV [01:00] 1.16 000000:02 class 0 VID 1a2c PID 4b61 > 9.76 HID [01:00] 1.16 000000:02 register HID > 9.37 USB3 root HUB port 3 init > 9.88 DEV [02:00] 3.32 000000:03 class 0 VID 0951 PID 1780 > 9.89 MSD device [02:00] 3.32 000000:03 conf 0 iface 0 ep 82#1024 01#1024 > 9.98 MSD [02:00] 3.32 000000:03 register MSD > 9.02 MSD [02:00] 3.32 000000:03 LUN 0 > 9.11 MSD READ_CAPACITY [02:00] 3.32 000000:03 lun 0 block-count 3907029168 block-size 512 > 9.91 MBR: 0x00008000, 32768 type: 0x0c > 9.92 MBR: 0x00000000, 0 type: 0x00 > 9.92 MBR: 0x00000000, 0 type: 0x00 > 9.92 MBR: 0x00010000,3906963632 type: 0xa6 This looks like good fdisk MBR: 0x0c is FAT32, 0xa6 is OpenBSD. > 9.32 Trying partition: 0 > 9.34 type: 16 lba: 32768 'BSD 4.4' ' ^ ' clusters 8167 (4) > 9.94 rsc 1 fat-sectors 32 root dir cluster 1 sectors 32 entries 512 > 9.94 FAT16 clusters 8167 > 9.95 [MSD [02:00] 3.32 000000:03] autoboot.txt not found > 9.95 Select partition rsts 0 C(boot_partition) 0 EEPROM config 0 result 1 > 9.61 Trying partition: 1 > 9.64 type: 16 lba: 32768 'BSD 4.4' ' ^ ' clusters 8167 (4) > 9.97 rsc 1 fat-sectors 32 root dir cluster 1 sectors 32 entries 512 > 9.97 FAT16 clusters 8167 > 9.80 Read config.txt bytes 65 hnd 0x28f > 9.98 [MSD [02:00] 3.32 000000:03] pieeprom.upd not found > 9.88 usb_max_current_enable default 0 max-current 5000 > 9.95 Read bcm2712-rpi-5-b.dtb bytes 78231 hnd 0x164 > 9.99 dt-match: compatible: raspberrypi,5-model-b match: brcm,bcm2712 > 10.00 dt-match: compatible: brcm,bcm2712 match: brcm,bcm2712 > 10.02 MESS:00:00:10.022474:0: *** Restart logging > 10.24 Read /config.txt bytes 65 hnd 0x28f > 10.02 MESS:00:00:10.029078:0: board: boardrev e04171 otp e04171 > 10.34 Read /config.txt bytes 65 hnd 0x28f And it reads the config.txt from the FAT partition: good. (What's in that config.txt? Have you tweaked it?) > 10.09 MESS:00:00:10.094092:0: Initial voltage 800000 temp 26289 > 10.29 MESS:00:00:10.294506:0: avs_2712: AVS pred 8807 880700 temp 26289 > 10.29 MESS:00:00:10.298109:0: vpred 880 mV +0 > 10.30 MESS:00:00:10.302316:0: over-voltage idle: 0 avs: 120700 delta: 0 (0x00000000) > 10.31 MESS:00:00:10.314448:0: FB framebuffer_swap 1 > 10.31 MESS:00:00:10.316314:0: Select resolution HDMI0/2 hotplug 0 max_mode 2 > 10.32 MESS:00:00:10.323203:0: Select resolution HDMI1/2 hotplug 0 max_mode 2 > 10.33 MESS:00:00:10.330685:0: dtb_file 'bcm2712-rpi-5-b.dtb' > 10.33 Loading 'bcm2712-rpi-5-b.dtb' to 0x00000000 offset 0x100 > 10.42 Read bcm2712-rpi-5-b.dtb bytes 78231 hnd 0x164 > 10.36 [MSD [02:00] 3.32 000000:03] /overlays/overlay_map.dtb not found > 10.70 /overlays/overlay_map.dtb > 10.74 Read /overlays/bcm2712d0.dtbo bytes 1363 hnd 0x1e76 > 10.39 MESS:00:00:10.399129:0: Loaded overlay 'bcm2712d0' > 10.47 PCIEx1: PWR 0 DET_WAKE 0 > 10.83 Read /config.txt bytes 65 hnd 0x28f > 10.85 Read /overlays/disable-bt.dtbo bytes 1073 hnd 0xfe6 > 10.50 MESS:00:00:10.503625:0: dterror: can't find symbol 'bt' > 10.50 MESS:00:00:10.506366:0: dterror: Failed to resolve overlay 'disable-bt' > 10.57 [MSD [02:00] 3.32 000000:03] /cmdline.txt not found > 10.79 /cmdline.txt > 10.58 MESS:00:00:10.581773:0: Failed to open command line file 'cmdline.txt' > 10.76 MESS:00:00:10.765781:0: RPM 106, max RPM 322 > 10.82 BMD "armstub8-2712.bin" not found > 10.27 fs_open: 'armstub8-2712.bin' > 10.83 Loading 'u-boot.bin' to 0x00000000 offset 0x200000 > 10.40 Read u-boot.bin bytes 697712 hnd 0xd41 And it reads das uboot: schmeckt gut. > 10.84 MESS:00:00:10.842764:0: Kernel relocated to 0x80000 > 10.84 MESS:00:00:10.847606:0: Device tree loaded to 0x2efec600 (size 0x1393b) > 10.85 PCI1 reset > 10.86 PCI2 reset > 10.87 set_reboot_order 0 > 10.87 set_reboot_arg1 0 > 10.87 USB-OTG disconnect > 10.91 MESS:00:00:10.919918:0: BSC_A no ACK > 10.92 MESS:00:00:10.921153:0: BSC_A no ACK > 10.92 MESS:00:00:10.925078:0: BSC_A no ACK > 10.94 MESS:00:00:10.949007:0: BSC_B no ACK > 10.95 MESS:00:00:10.950234:0: BSC_B no ACK > 10.95 MESS:00:00:10.954169:0: BSC_B no ACK > 10.97 MESS:00:00:10.977940:0: Starting OS 10977 ms > 10.98 MESS:00:00:10.983551:0: 00000040: -> 00000480 > 10.98 MESS:00:00:10.985405:0: 00000030: -> 00100080 > 10.99 MESS:00:00:10.990118:0: 00000034: -> 00100080 > 10.99 MESS:00:00:10.994830:0: 00000038: -> 00100080 > 10.99 MESS:00:00:10.999544:0: 0000003c: -> 00100080 > > NOTICE: BL31: v2.6(release):v2.6-240-gfc45bc492 > NOTICE: BL31: Built : 12:55:13, Dec 4 2024 > > > U-Boot 2025.07 (Mar 02 2026 - 10:13:27 -0700) > > DRAM: 1020 MiB (total 16 GiB) > RPI 5 Model B (0xe04171) > Core: 25 devices, 11 uclasses, devicetree: board > MMC: mmc@fff000: 0, mmc@1100000: 1 > Loading Environment from FAT... Card did not respond to voltage select! : -110 > ** Bad device specification mmc 0 ** > In: serial,usbkbd > Out: serial,vidconsole > Err: serial,vidconsole > Net: No ethernet found. > > starting USB... > No USB controllers found > scanning usb for storage devices... 0 Storage Device(s) found Not good: if no usb devices are found, surely it won't boot from your usb disk. > Hit any key to stop autoboot: 0 > Card did not respond to voltage select! : -110 What card? The removed sdmmc? > Cannot persist EFI variables without system partition > Card did not respond to voltage select! : -110 > U-Boot> boot > Card did not respond to voltage select! : -110 > U-Boot> setenv bootdelay -2 > U-Boot> saveenv > Saving Environment to FAT... Card did not respond to voltage select! : -110 > ** Bad device specification mmc 0 ** > Failed (1) > U-Boot> boot > Card did not respond to voltage select! : -110 > U-Boot>
No comments:
Post a Comment