Hi Chris,
I decided to sell the board and get a different one..
But for others wanting to use this board in the future.
I tried both USB and PS2 Native (no adapter) keyboards. Neither work after
the installer starts.
Bearing in mind none of the SATA ports are detected either..
Cheers, Andy.
On Wed, Nov 21, 2018 at 3:42 AM Chris Cappuccio <chris@nmedia.net> wrote:
> Andrew Lemin [andrew.lemin@gmail.com] wrote:
> > Hi,
> >
> > I am running an ASRock J4105B-ITX board and wanting to run OpenBSD on
> this.
> > https://www.asrock.com/MB/Intel/J4105B-ITX/index.asp#BIOS
> >
> > It boots up, and at the 'boot>' prompt I can use the keyboard find.
> >
> > However after it boots up, the keyboard stops working, and no disks are
> > found by the installer (used auto_install to send test commands).
> > It appears that there is no chipset support, for the Intel Celeron J4105
> > CPU from what I can work out.
> >
> > To test that it was working fine and is just OpebBSD which is not
> working,
> > I installed Linux and have included the dmesg below (from Linux).
> > I cannot run a dmesg from the OpenBSD installer as I cannot use the
> > keyboard etc.
> >
>
> The ASRock J4205-ITX (Apollo Lake) works fine, so does the J3710-ITX
> (Braswell).
>
> I use them both headless, but they work fine when I plug in a USB keyboard.
>
> The J4105-ITX (Gemini Lake) is newer than either.
>
> What kind of keyboard are you using? If it's not USB, plug in a USB
> keyboard.
> Although it may not work at the boot> prompt, it will work once you are
> booted
> up.
>
> For fun, here are dmesg for the older versions of your board. They both
> work
> with USB input devices.
>
> Braswell
> --------
>
> OpenBSD 6.3-current (GENERIC.MP) #21: Fri Jun 29 17:32:47 PDT 2018
> chris@r8.nmedia.net:/usr/src/sys/arch/amd64/compile/GENERIC.MP
> real mem = 8023584768 (7651MB)
> avail mem = 7771283456 (7411MB)
> mpath0 at root
> scsibus0 at mpath0: 256 targets
> mainbus0 at root
> bios0 at mainbus0: SMBIOS rev. 2.8 @ 0xecec0 (18 entries)
> bios0: vendor American Megatrends Inc. version "P1.30" date 03/30/2016
> bios0: ASRock J3710-ITX
> acpi0 at bios0: rev 2
> acpi0: sleep states S0 S3 S4 S5
> acpi0: tables DSDT FACP APIC FPDT FIDT AAFT MCFG HPET SSDT SSDT SSDT UEFI
> LPIT CSRT
> acpi0: wakeup devices UAR1(S4) XHC1(S4) HDEF(S4) PXSX(S4) RP01(S4)
> PXSX(S4) RP02(S4) PXSX(S4) RP03(S4) PXSX(S4) RP04(S4) BRCM(S0) PWRB(S4)
> acpitimer0 at acpi0: 3579545 Hz, 24 bits
> acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> cpu0 at mainbus0: apid 0 (boot processor)
> cpu0: Intel(R) Pentium(R) CPU J3710 @ 1.60GHz, 1600.37 MHz
> cpu0:
> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,AES,RDRAND,NXE,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS,SENSOR,ARAT,MELTDOWN
> cpu0: 1MB 64b/line 16-way L2 cache
> cpu0: smt 0, core 0, package 0
> mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
> cpu0: apic clock running at 79MHz
> cpu0: mwait min=64, max=64, C-substates=0.2.0.0.0.0.3.3, IBE
> cpu1 at mainbus0: apid 2 (application processor)
> cpu1: Intel(R) Pentium(R) CPU J3710 @ 1.60GHz, 1600.00 MHz
> cpu1:
> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,AES,RDRAND,NXE,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS,SENSOR,ARAT,MELTDOWN
> cpu1: 1MB 64b/line 16-way L2 cache
> cpu1: smt 0, core 1, package 0
> cpu2 at mainbus0: apid 4 (application processor)
> cpu2: Intel(R) Pentium(R) CPU J3710 @ 1.60GHz, 1600.00 MHz
> cpu2:
> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,AES,RDRAND,NXE,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS,SENSOR,ARAT,MELTDOWN
> cpu2: 1MB 64b/line 16-way L2 cache
> cpu2: smt 0, core 2, package 0
> cpu3 at mainbus0: apid 6 (application processor)
> cpu3: Intel(R) Pentium(R) CPU J3710 @ 1.60GHz, 1600.00 MHz
> cpu3:
> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,AES,RDRAND,NXE,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS,SENSOR,ARAT,MELTDOWN
> cpu3: 1MB 64b/line 16-way L2 cache
> cpu3: smt 0, core 3, package 0
> ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 115 pins
> acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255
> acpihpet0 at acpi0: 14318179 Hz
> acpiprt0 at acpi0: bus 0 (PCI0)
> acpiprt1 at acpi0: bus 1 (RP01)
> acpiprt2 at acpi0: bus 2 (RP02)
> acpiprt3 at acpi0: bus 3 (RP03)
> acpiprt4 at acpi0: bus 4 (RP04)
> acpiec0 at acpi0: not present
> acpicpu0 at acpi0: C3(10@1000 mwait.1@0x64), C2(10@500 mwait.1@0x58),
> C1(1000@1 mwait.1), PSS
> acpicpu1 at acpi0: C3(10@1000 mwait.1@0x64), C2(10@500 mwait.1@0x58),
> C1(1000@1 mwait.1), PSS
> acpicpu2 at acpi0: C3(10@1000 mwait.1@0x64), C2(10@500 mwait.1@0x58),
> C1(1000@1 mwait.1), PSS
> acpicpu3 at acpi0: C3(10@1000 mwait.1@0x64), C2(10@500 mwait.1@0x58),
> C1(1000@1 mwait.1), PSS
> acpipwrres0 at acpi0: CLK0, resource for CAMD
> acpipwrres1 at acpi0: CLK0, resource for CAM1
> acpipwrres2 at acpi0: CLK1, resource for CAM2, CAM3
> acpipwrres3 at acpi0: USBC, resource for XHC1
> acpicmos0 at acpi0
> "BCM43241" at acpi0 not configured
> "BCM2E64" at acpi0 not configured
> "BCM4752" at acpi0 not configured
> "SMO91D0" at acpi0 not configured
> "INT33F7" at acpi0 not configured
> "INT33BE" at acpi0 not configured
> "INTCF1C" at acpi0 not configured
> "MSFT0002" at acpi0 not configured
> acpibtn0 at acpi0: PWRB
> acpibtn1 at acpi0: SLPB
> acpivideo0 at acpi0: GFX0
> acpivout0 at acpivideo0: DD1F
> cpu0: Enhanced SpeedStep 1600 MHz: speeds: 1601, 1600, 1520, 1440, 1360,
> 1280, 1200, 1120, 1040, 960, 880, 800, 720, 640, 560, 480 MHz
> pci0 at mainbus0 bus 0
> pchb0 at pci0 dev 0 function 0 "Intel Braswell Host" rev 0x35
> inteldrm0 at pci0 dev 2 function 0 "Intel HD Graphics" rev 0x35
> drm0 at inteldrm0
> inteldrm0: msi
> inteldrm0: 1024x768, 32bpp
> wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation)
> wsdisplay0: screen 1-5 added (std, vt100 emulation)
> ahci0 at pci0 dev 19 function 0 "Intel Braswell AHCI" rev 0x35: msi, AHCI
> 1.3.1
> ahci0: port 0: 6.0Gb/s
> ahci0: port 1: 6.0Gb/s
> scsibus1 at ahci0: 32 targets
> sd0 at scsibus1 targ 0 lun 0: <ATA, HFS250G32TND-N1A, 3000> SCSI3 0/direct
> fixed t10.ATA_HFS250G32TND-N1A2A_FS67N121611207N6G_
> sd0: 238475MB, 512 bytes/sector, 488397168 sectors, thin
> sd1 at scsibus1 targ 1 lun 0: <ATA, ST2000DM001-1CH1, CC27> SCSI3 0/direct
> fixed naa.5000c500653bc225
> sd1: 1907729MB, 512 bytes/sector, 3907029168 sectors
> xhci0 at pci0 dev 20 function 0 "Intel Braswell xHCI" rev 0x35: msi, xHCI
> 1.0
> usb0 at xhci0: USB revision 3.0
> uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev
> 3.00/1.00 addr 1
> "Intel Braswell TXE" rev 0x35 at pci0 dev 26 function 0 not configured
> ppb0 at pci0 dev 28 function 0 "Intel Braswell PCIE" rev 0x35: msi
> pci1 at ppb0 bus 1
> ppb1 at pci0 dev 28 function 1 "Intel Braswell PCIE" rev 0x35: msi
> pci2 at ppb1 bus 2
> ppb2 at pci0 dev 28 function 2 "Intel Braswell PCIE" rev 0x35: msi
> pci3 at ppb2 bus 3
> re0 at pci3 dev 0 function 0 "Realtek 8168" rev 0x11: RTL8168G/8111G
> (0x4c00), msi, address 70:85:c2:05:57:e7
> rgephy0 at re0 phy 7: RTL8251 PHY, rev. 0
> ppb3 at pci0 dev 28 function 3 "Intel Braswell PCIE" rev 0x35: msi
> pci4 at ppb3 bus 4
> ahci1 at pci4 dev 0 function 0 "ASMedia ASM1061 AHCI" rev 0x02: msi, AHCI
> 1.2
> scsibus2 at ahci1: 32 targets
> pcib0 at pci0 dev 31 function 0 "Intel Braswell PCU LPC" rev 0x35
> ichiic0 at pci0 dev 31 function 3 "Intel Braswell SMBus" rev 0x35: apic 1
> int 18
> iic0 at ichiic0
> spdmem0 at iic0 addr 0x50: 4GB DDR3 SDRAM PC3-12800 SO-DIMM
> spdmem1 at iic0 addr 0x51: 4GB DDR3 SDRAM PC3-12800 SO-DIMM
> isa0 at pcib0
> isadma0 at isa0
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> pckbc0 at isa0 port 0x60/5 irq 1 irq 12
> pckbd0 at pckbc0 (kbd slot)
> wskbd0 at pckbd0: console keyboard, using wsdisplay0
> pcppi0 at isa0 port 0x61
> spkr0 at pcppi0
> wbsio0 at isa0 port 0x2e/2: NCT6776F rev 0x33
> lm1 at wbsio0 port 0x290/8: NCT6776F
> vmm0 at mainbus0: VMX/EPT
> uhub1 at uhub0 port 1 configuration 1 interface 0 "ASMedia AS2107" rev
> 2.10/0.01 addr 2
> uhub2 at uhub0 port 5 configuration 1 interface 0 "Genesys Logic USB2.0
> Hub" rev 2.00/88.31 addr 3
> uhub3 at uhub0 port 8 configuration 1 interface 0 "ASMedia AS2107" rev
> 3.00/0.01 addr 4
> vscsi0 at root
> scsibus3 at vscsi0: 256 targets
> softraid0 at root
> scsibus4 at softraid0: 256 targets
> root on sd0a (9c842068a9b98834.a) swap on sd0b dump on sd0b
>
>
> Apollo Lake
> -----------
>
> OpenBSD 6.4 (GENERIC.MP) #0: Sat Nov 17 22:15:46 CET 2018
> root@syspatch-64-amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/
> GENERIC.MP
> real mem = 8209932288 (7829MB)
> avail mem = 7951843328 (7583MB)
> mpath0 at root
> scsibus0 at mpath0: 256 targets
> mainbus0 at root
> bios0 at mainbus0: SMBIOS rev. 3.0 @ 0xed450 (18 entries)
> bios0: vendor American Megatrends Inc. version "P1.30" date 04/18/2017
> bios0: ASRock J4205-ITX
> acpi0 at bios0: rev 2
> acpi0: sleep states S0 S3 S4 S5
> acpi0: tables DSDT FACP FPDT FIDT MCFG DBG2 DBGP HPET LPIT APIC NPKT PRAM
> WSMT SSDT SSDT AAFT SSDT SSDT SSDT SSDT SSDT UEFI WDAT
> acpi0: wakeup devices SIO1(S3) UAR1(S4) HDAS(S3) XHC_(S4) XDCI(S4)
> BRCM(S0) PXSX(S4) RP01(S4) PXSX(S4) RP02(S4) PXSX(S4) RP03(S4) PXSX(S4)
> RP04(S4) PXSX(S4) RP05(S4) [...]
> acpitimer0 at acpi0: 3579545 Hz, 32 bits
> acpimcfg0 at acpi0
> acpimcfg0: addr 0xe0000000, bus 0-255
> acpihpet0 at acpi0: 19200000 Hz
> acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> cpu0 at mainbus0: apid 0 (boot processor)
> cpu0: Intel(R) Pentium(R) CPU J4205 @ 1.50GHz, 1497.01 MHz, 06-5c-09
> cpu0:
> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,SMEP,ERMS,MPX,RDSEED,SMAP,CLFLUSHOPT,PT,SHA,IBRS,IBPB,STIBP,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES,MELTDOWN
> cpu0: 1MB 64b/line 16-way L2 cache
> cpu0: smt 0, core 0, package 0
> mtrr: Pentium Pro MTRR support, 10 var ranges, 88 fixed ranges
> cpu0: apic clock running at 19MHz
> cpu0: mwait min=64, max=64, C-substates=0.2.0.2.4.2.1.1, IBE
> cpu1 at mainbus0: apid 2 (application processor)
> cpu1: Intel(R) Pentium(R) CPU J4205 @ 1.50GHz, 1496.56 MHz, 06-5c-09
> cpu1:
> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,SMEP,ERMS,MPX,RDSEED,SMAP,CLFLUSHOPT,PT,SHA,IBRS,IBPB,STIBP,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES,MELTDOWN
> cpu1: 1MB 64b/line 16-way L2 cache
> cpu1: smt 0, core 1, package 0
> cpu2 at mainbus0: apid 4 (application processor)
> cpu2: Intel(R) Pentium(R) CPU J4205 @ 1.50GHz, 1496.56 MHz, 06-5c-09
> cpu2:
> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,SMEP,ERMS,MPX,RDSEED,SMAP,CLFLUSHOPT,PT,SHA,IBRS,IBPB,STIBP,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES,MELTDOWN
> cpu2: 1MB 64b/line 16-way L2 cache
> cpu2: smt 0, core 2, package 0
> cpu3 at mainbus0: apid 6 (application processor)
> cpu3: Intel(R) Pentium(R) CPU J4205 @ 1.50GHz, 1496.56 MHz, 06-5c-09
> cpu3:
> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,SMEP,ERMS,MPX,RDSEED,SMAP,CLFLUSHOPT,PT,SHA,IBRS,IBPB,STIBP,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES,MELTDOWN
> cpu3: 1MB 64b/line 16-way L2 cache
> cpu3: smt 0, core 3, package 0
> ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 120 pins
> acpiprt0 at acpi0: bus 0 (PCI0)
> acpiprt1 at acpi0: bus 1 (RP03)
> acpiprt2 at acpi0: bus 2 (RP04)
> acpiprt3 at acpi0: bus 3 (RP05)
> acpiprt4 at acpi0: bus 4 (RP06)
> acpiec0 at acpi0: not present
> acpicpu0 at acpi0: C3(10@150 mwait.1@0x60), C2(10@50 mwait.1@0x21),
> C1(1000@1 mwait.1@0x1), PSS
> acpicpu1 at acpi0: C3(10@150 mwait.1@0x60), C2(10@50 mwait.1@0x21),
> C1(1000@1 mwait.1@0x1), PSS
> acpicpu2 at acpi0: C3(10@150 mwait.1@0x60), C2(10@50 mwait.1@0x21),
> C1(1000@1 mwait.1@0x1), PSS
> acpicpu3 at acpi0: C3(10@150 mwait.1@0x60), C2(10@50 mwait.1@0x21),
> C1(1000@1 mwait.1@0x1), PSS
> acpipwrres0 at acpi0: FN00, resource for FAN0
> acpitz0 at acpi0: critical temperature is 100 degC
> acpicmos0 at acpi0
> acpibtn0 at acpi0: PWRB
> "INT3452" at acpi0 not configured
> "INT3452" at acpi0 not configured
> "INT3452" at acpi0 not configured
> "INT3452" at acpi0 not configured
> "INT33A1" at acpi0 not configured
> "PNP0C0B" at acpi0 not configured
> acpivideo0 at acpi0: GFX0
> acpivout0 at acpivideo0: DD1F
> cpu0: Enhanced SpeedStep 1497 MHz: speeds: 1501, 1500, 1400, 1300, 1200,
> 1100, 1000, 900, 800 MHz
> pci0 at mainbus0 bus 0
> pchb0 at pci0 dev 0 function 0 "Intel Apollo Lake Host" rev 0x0b
> inteldrm0 at pci0 dev 2 function 0 vendor "Intel", unknown product 0x5a84
> rev 0x0b
> drm0 at inteldrm0
> inteldrm0: msi
> error: [drm:pid0:i915_firmware_load_error_print] *ERROR* failed to load
> firmware i915/bxt_dmc_ver1.bin (-22)
> error: [drm:pid0:i915_gem_init_hw] *ERROR* Failed to initialize GuC, error
> -8 (ignored)
> inteldrm0: 1024x768, 32bpp
> Unclaimed register detected after writing to register 0x68970
> wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation)
> wsdisplay0: screen 1-5 added (std, vt100 emulation)
> "Intel Apollo Lake TXE" rev 0x0b at pci0 dev 15 function 0 not configured
> ahci0 at pci0 dev 18 function 0 "Intel Apollo Lake AHCI" rev 0x0b: msi,
> AHCI 1.3.1
> ahci0: port 0: 6.0Gb/s
> ahci0: port 1: 6.0Gb/s
> scsibus1 at ahci0: 32 targets
> sd0 at scsibus1 targ 0 lun 0: <ATA, INTEL SSDSC2BB24, D201> SCSI3 0/direct
> fixed naa.55cd2e404c522549
> sd0: 228936MB, 512 bytes/sector, 468862128 sectors, thin
> sd1 at scsibus1 targ 1 lun 0: <ATA, INTEL SSDSC2BB24, D201> SCSI3 0/direct
> fixed naa.55cd2e404c521c42
> sd1: 228936MB, 512 bytes/sector, 468862128 sectors, thin
> ppb0 at pci0 dev 19 function 0 "Intel Apollo Lake PCIE" rev 0xfb: msi
> pci1 at ppb0 bus 1
> re0 at pci1 dev 0 function 0 "Realtek 8168" rev 0x11: RTL8168G/8111G
> (0x4c00), msi, address 70:85:c2:43:c0:f8
> rgephy0 at re0 phy 7: RTL8251 PHY, rev. 0
> ppb1 at pci0 dev 19 function 1 "Intel Apollo Lake PCIE" rev 0xfb: msi
> pci2 at ppb1 bus 2
> ppb2 at pci0 dev 19 function 2 "Intel Apollo Lake PCIE" rev 0xfb: msi
> pci3 at ppb2 bus 3
> ahci1 at pci3 dev 0 function 0 "ASMedia ASM1061 AHCI" rev 0x02: msi, AHCI
> 1.2
> ahci1: port 0: 6.0Gb/s
> ahci1: port 1: 6.0Gb/s
> scsibus2 at ahci1: 32 targets
> sd2 at scsibus2 targ 0 lun 0: <ATA, Crucial_CT480M50, MU05> SCSI3 0/direct
> fixed naa.500a07510c263e53
> sd2: 457862MB, 512 bytes/sector, 937703088 sectors, thin
> sd3 at scsibus2 targ 1 lun 0: <ATA, Crucial_CT480M50, MU05> SCSI3 0/direct
> fixed naa.500a07510c263e41
> sd3: 457862MB, 512 bytes/sector, 937703088 sectors, thin
> ppb3 at pci0 dev 19 function 3 vendor "Intel", unknown product 0x5adb rev
> 0xfb: msi
> pci4 at ppb3 bus 4
> xhci0 at pci0 dev 21 function 0 "Intel Apollo Lake xHCI" rev 0x0b: msi,
> xHCI 1.0
> usb0 at xhci0: USB revision 3.0
> uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev
> 3.00/1.00 addr 1
> pcib0 at pci0 dev 31 function 0 "Intel Apollo Lake LPC" rev 0x0b
> ichiic0 at pci0 dev 31 function 1 "Intel Apollo Lake SMBus" rev 0x0b:
> polling
> iic0 at ichiic0
> spdmem0 at iic0 addr 0x50: 4GB DDR3 SDRAM PC3-12800 SO-DIMM
> spdmem1 at iic0 addr 0x52: 4GB DDR3 SDRAM PC3-12800 SO-DIMM
> isa0 at pcib0
> isadma0 at isa0
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> pckbc0 at isa0 port 0x60/5 irq 1 irq 12
> pckbd0 at pckbc0 (kbd slot)
> wskbd0 at pckbd0: console keyboard, using wsdisplay0
> pcppi0 at isa0 port 0x61
> spkr0 at pcppi0
> lpt0 at isa0 port 0x378/4 irq 7
> vmm0 at mainbus0: VMX/EPT
> vscsi0 at root
> scsibus3 at vscsi0: 256 targets
> softraid0 at root
> scsibus4 at softraid0: 256 targets
> sd4 at scsibus4 targ 1 lun 0: <OPENBSD, SR RAID 1, 006> SCSI2 0/direct
> fixed
> sd4: 228933MB, 512 bytes/sector, 468856433 sectors
> sd5 at scsibus4 targ 2 lun 0: <OPENBSD, SR RAID 1, 006> SCSI2 0/direct
> fixed
> sd5: 457860MB, 512 bytes/sector, 937697393 sectors
> root on sd4a (dd533a2b98d638c9.a) swap on sd4b dump on sd4b
>
No comments:
Post a Comment