Hi,
thanks for your reply.
It was a new installation on this notebook so I had to change the SO.
With FreeBSD (11.2) no problem for this interface.
But theconfiguration of the sound cart is a bit difficult.
On OpenBSD was most simple to configure.
Il 30/12/20 23:46, pcost ha scritto:
> Ciao Luciano,
> I am writing using the same notebook you have, an Acer Extensa 5635,
> with 4GB Ram.
> My Bios version is 1.3311 and OpenBSD version is 6.8.
> Same behavior here: the wifi card works correctly only with one memory
> card inserted (2GB); inserting the second memory card (2+2GB), the
> wifi card stops to work.
> The 'dmesg' output is almost the same of yours
> (alc0: phy write timeout: phy 0, reg 30) and so on.
> I confirm everything works correctly with debian (kernel 5.9).
> My workaround is to use a TPLink mini usb wifi network card, that is
> better than decrease the ram...
> Ciao.
>
>
> Il 12/20/20 8:08 PM, Isaia Luciano ha scritto:
>> Hello,
>>
>> it would seam a OpenBSB problem, the other SO (Linux, FreeBSD)
>> properly activate the interface.
>>
>>
>> # sh /etc/netstart alc0
>> alc0: writev(DHCPDISCOVER): No buffer space available
>> alc0: writev(DHCPDISCOVER): No buffer space available
>> alc0: writev(DHCPDISCOVER): No buffer space available
>> alc0: no lease....alc0: writev(DHCPDISCOVER): No buffer space available
>> .alc0: writev(DHCPDISCOVER): No buffer space available
>> .alc0: writev(DHCPDISCOVER): No buffer space avialable
>> .alc0: writev(DHCPDISCOVER): No buffer space available
>> .alc0: writev(DHCPDISCOVER): No buffer space available
>> .alc0: writev(DHCPDISCOVER): No buffer space available
>> .alc0: writev(DHCPDISCOVER): No buffer space available
>> sleeping
>>
>> # ifconfig alc0 down
>> alc0: could not disable RxQ/TxQ (0xffffffff)!
>> alc0: could not disable Rx/Tx MAC(0xffffffff)!
>>
>>
>> I tried with live CD of Sistem Rescue CD and MidnighBSD.
>> It has already happened to someone.
>>
>> Thanks.
>>
>> Luciano.
>>
>> Il 19/12/20 11:36, luisaia@tin.it ha scritto:
>>> Hi,I have install OpenBSD 6.8 on Acer Laptop with 2GB of RAM.
>>> I have upgrade the memory added a new 2 GB RAM bank.On boot the net
>>> interface not running.The dmesg is:
>>> OpenBSD 6.8 (GENERIC.MP) #98: Sun Oct 4 18:13:26 MDT 2020
>>> deraadt@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
>>> real mem = 4105977856 (3915MB)
>>> avail mem = 3966488576 (3782MB)
>>> random: good seed from bootblocks
>>> mpath0 at root
>>> scsibus0 at mpath0: 256 targets
>>> mainbus0 at root
>>> bios0 at mainbus0: SMBIOS rev. 2.5 @ 0xb5ec0000 (33 entries)
>>> bios0: vendor Phoenix version "V1.3311" date 12/21/2009
>>> bios0: Acer Extensa 5635Z
>>> acpi0 at bios0: ACPI 3.0
>>> acpi0: sleep states S0 S3 S4 S5
>>> acpi0: tables DSDT FACP HPET MCFG APIC BOOT SSDT SSDT SSDT SSDT
>>> acpi0: wakeup devices USB0(S3) USB1(S3) USBR(S3) EHC1(S3) USB3(S3)
>>> EHC2(S3) HDEF(S3) GLAN(S4)
>>> acpitimer0 at acpi0: 3579545 Hz, 24 bits
>>> acpihpet0 at acpi0: 14318179 Hz
>>> acpimcfg0 at acpi0
>>> acpimcfg0: addr 0xe0000000, bus 0-255
>>> acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
>>> cpu0 at mainbus0: apid 0 (boot processor)
>>> cpu0: Pentium(R) Dual-Core CPU T4300 @ 2.10GHz, 2095.34 MHz, 06-17-0a
>>> cpu0:
>>> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM,XSAVE,NXE,LONG,LAHF,PERF,SENSOR,MELTDOWN
>>>
>>> cpu0: 1MB 64b/line 4-way L2 cache
>>> cpu0: smt 0, core 0, package 0
>>> mtrr: Pentium Pro MTRR support, 7 var ranges, 88 fixed ranges
>>> cpu0: apic clock running at 199MHz
>>> cpu0: mwait min=64, max=64, C-substates=0.2.2.2, IBE
>>> cpu1 at mainbus0: apid 1 (application processor)
>>> cpu1: Pentium(R) Dual-Core CPU T4300 @ 2.10GHz, 2094.99 MHz, 06-17-0a
>>> cpu1:
>>> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM,XSAVE,NXE,LONG,LAHF,PERF,SENSOR,MELTDOWN
>>>
>>> cpu1: 1MB 64b/line 4-way L2 cache
>>> cpu1: smt 0, core 1, package 0
>>> ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
>>> acpiprt0 at acpi0: bus 0 (PCI0)
>>> acpiprt1 at acpi0: bus 10 (P0P1)
>>> acpiprt2 at acpi0: bus 2 (RP01)
>>> acpiprt3 at acpi0: bus -1 (RP02)
>>> acpiprt4 at acpi0: bus -1 (RP03)
>>> acpiprt5 at acpi0: bus 7 (RP04)
>>> acpiprt6 at acpi0: bus -1 (RP05)
>>> acpiec0 at acpi0
>>> acpiac0 at acpi0: AC unit online
>>> acpibat0 at acpi0: BAT1 model "AS09C31" serial 9418 type LION oem
>>> "SANYO"
>>> acpibtn0 at acpi0: LID_
>>> acpibtn1 at acpi0: PWRB
>>> acpibtn2 at acpi0: SLPB
>>> "PNP0C14" at acpi0 not configured
>>> acpipci0 at acpi0 PCI0
>>> acpicmos0 at acpi0
>>> "SYN1B20" at acpi0 not configured
>>> "PNP0C14" at acpi0 not configured
>>> acpicpu0 at acpi0: !C3(250@17 mwait.3@0x20), !C2(500@1
>>> mwait.1@0x10), C1(1000@1 mwait.1), PSS
>>> acpicpu1 at acpi0: !C3(250@17 mwait.3@0x20), !C2(500@1
>>> mwait.1@0x10), C1(1000@1 mwait.1), PSS
>>> acpitz0 at acpi0: critical temperature is 108 degC
>>> acpivideo0 at acpi0: VGA_
>>> acpivideo1 at acpi0: GFX0
>>> acpivout0 at acpivideo1: DD02
>>> cpu0: Enhanced SpeedStep 2095 MHz: speeds: 2100, 1600, 1200 MHz
>>> pci0 at mainbus0 bus 0
>>> pchb0 at pci0 dev 0 function 0 "Intel GM45 Host" rev 0x07
>>> inteldrm0 at pci0 dev 2 function 0 "Intel GM45 Video" rev 0x07
>>> drm0 at inteldrm0
>>> intagp0 at inteldrm0
>>> agp0 at intagp0: aperture at 0xd0000000, size 0x10000000
>>> inteldrm0: apic 2 int 16, GM45, gen 4
>>> "Intel GM45 Video" rev 0x07 at pci0 dev 2 function 1 not configured
>>> uhci0 at pci0 dev 26 function 0 "Intel 82801I USB" rev 0x03: apic 2
>>> int 16
>>> uhci1 at pci0 dev 26 function 1 "Intel 82801I USB" rev 0x03: apic 2
>>> int 21
>>> ehci0 at pci0 dev 26 function 7 "Intel 82801I USB" rev 0x03: apic 2
>>> int 19
>>> usb0 at ehci0: USB revision 2.0
>>> uhub0 at usb0 configuration 1 interface 0 "Intel EHCI root hub" rev
>>> 2.00/1.00 addr 1
>>> azalia0 at pci0 dev 27 function 0 "Intel 82801I HD Audio" rev 0x03: msi
>>> azalia0: codecs: Conexant CX20561
>>> audio0 at azalia0
>>> ppb0 at pci0 dev 28 function 0 "Intel 82801I PCIE" rev 0x03: msi
>>> pci1 at ppb0 bus 2
>>> ppb1 at pci0 dev 28 function 3 "Intel 82801I PCIE" rev 0x03: msi
>>> pci2 at ppb1 bus 7
>>> athn0 at pci2 dev 0 function 0 "Atheros AR9281" rev 0x01: apic 2 int 19
>>> athn0: could not reset chip
>>> ppb2 at pci0 dev 28 function 5 "Intel 82801I PCIE" rev 0x03: msi
>>> pci3 at ppb2 bus 9
>>> alc0 at pci3 dev 0 function 0 "Attansic Technology L1C" rev 0xc0:
>>> msialc0: phy write timeout: phy 0, reg 29
>>> alc0: phy write timeout: phy 0, reg 30
>>> alc0: phy write timeout: phy 0, reg 29
>>> alc0: phy write timeout: phy 0, reg 30
>>> alc0: phy write timeout: phy 0, reg 29
>>> alc0: phy write timeout: phy 0, reg 30
>>> alc0: phy write timeout: phy 0, reg 29
>>> alc0: phy write timeout: phy 0, reg 30
>>> alc0: phy write timeout: phy 0, reg 29
>>> alc0: phy write timeout: phy 0, reg 30
>>> alc0: phy write timeout: phy 0, reg 29
>>> alc0: phy write timeout: phy 0, reg 30
>>> alc0: phy write timeout: phy 0, reg 29
>>> alc0: phy read timeout: phy 0, reg 30
>>> alc0: phy write timeout: phy 0, reg 30
>>> alc0: phy write timeout: phy 0, reg 29
>>> alc0: phy read timeout: phy 0, reg 30
>>> alc0: phy write timeout: phy 0, reg 30
>>> alc0: could not disable RxQ/TxQ (0xffffffff)!
>>> alc0: could not disable Rx/Tx MAC(0xffffffff)!
>>> alc0: master reset timeout!
>>> alc0: reset timeout(0xffffffff)!
>>> alc0: reloading EEPROM timeout!
>>> , address ff:ff:ff:ff:ff:ff
>>> alc0: phy read timeout: phy 0, reg 1
>>> alc0: no PHY found!
>>> uhci2 at pci0 dev 29 function 0 "Intel 82801I USB" rev 0x03: apic 2
>>> int 23
>>> uhci3 at pci0 dev 29 function 1 "Intel 82801I USB" rev 0x03: apic 2
>>> int 19
>>> uhci4 at pci0 dev 29 function 2 "Intel 82801I USB" rev 0x03: apic 2
>>> int 18
>>> uhci5 at pci0 dev 29 function 3 "Intel 82801I USB" rev 0x03: apic 2
>>> int 16
>>> ehci1 at pci0 dev 29 function 7 "Intel 82801I USB" rev 0x03: apic 2
>>> int 23
>>> usb1 at ehci1: USB revision 2.0
>>> uhub1 at usb1 configuration 1 interface 0 "Intel EHCI root hub" rev
>>> 2.00/1.00 addr 1
>>> ppb3 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0x93
>>> pci4 at ppb3 bus 10
>>> pcib0 at pci0 dev 31 function 0 "Intel 82801IBM LPC" rev 0x03
>>> ahci0 at pci0 dev 31 function 2 "Intel 82801I AHCI" rev 0x03: msi,
>>> AHCI 1.2
>>> ahci0: port 0: 3.0Gb/s
>>> ahci0: port 1: 1.5Gb/s
>>> ahci0: PHY offline on port 4
>>> ahci0: PHY offline on port 5
>>> scsibus1 at ahci0: 32 targets
>>> sd0 at scsibus1 targ 0 lun 0: <ATA, CT120BX500SSD1, M6C>
>>> naa.0000000000000000
>>> sd0: 114473MB, 512 bytes/sector, 234441648 sectors, thin
>>> cd0 at scsibus1 targ 1 lun 0: <TSSTcorp, CDDVDW TS-L633C, AC01>
>>> removable
>>> ichiic0 at pci0 dev 31 function 3 "Intel 82801I SMBus" rev 0x03:
>>> apic 2 int 19
>>> iic0 at ichiic0
>>> spdmem0 at iic0 addr 0x50: 2GB DDR3 SDRAM PC3-8500 SO-DIMM
>>> spdmem1 at iic0 addr 0x52: 2GB DDR3 SDRAM PC3-8500 SO-DIMM
>>> usb2 at uhci0: USB revision 1.0
>>> uhub2 at usb2 configuration 1 interface 0 "Intel UHCI root hub" rev
>>> 1.00/1.00 addr 1
>>> usb3 at uhci1: USB revision 1.0
>>> uhub3 at usb3 configuration 1 interface 0 "Intel UHCI root hub" rev
>>> 1.00/1.00 addr 1
>>> usb4 at uhci2: USB revision 1.0
>>> uhub4 at usb4 configuration 1 interface 0 "Intel UHCI root hub" rev
>>> 1.00/1.00 addr 1
>>> usb5 at uhci3: USB revision 1.0
>>> uhub5 at usb5 configuration 1 interface 0 "Intel UHCI root hub" rev
>>> 1.00/1.00 addr 1
>>> usb6 at uhci4: USB revision 1.0
>>> uhub6 at usb6 configuration 1 interface 0 "Intel UHCI root hub" rev
>>> 1.00/1.00 addr 1
>>> usb7 at uhci5: USB revision 1.0
>>> uhub7 at usb7 configuration 1 interface 0 "Intel UHCI root hub" rev
>>> 1.00/1.00 addr 1
>>> isa0 at pcib0
>>> isadma0 at isa0
>>> pckbc0 at isa0 port 0x60/5 irq 1 irq 12
>>> pckbd0 at pckbc0 (kbd slot)
>>> wskbd0 at pckbd0: console keyboard
>>> pms0 at pckbc0 (aux slot)
>>> wsmouse0 at pms0 mux 0
>>> pms0: Synaptics touchpad, firmware 7.2, 0x1c0b1 0xa44000 0x0
>>> 0xd04731 0xa0000
>>> pcppi0 at isa0 port 0x61
>>> spkr0 at pcppi0
>>> uvideo0 at uhub1 port 8 configuration 1 interface 0 "SuYin Video
>>> WebCam" rev 2.00/5.00 addr 2
>>> video0 at uvideo0
>>> uhidev0 at uhub4 port 1 configuration 1 interface 0 "2.4G 2.4G
>>> Wireless Device" rev 1.10/10.01 addr 2
>>> uhidev0: iclass 3/1
>>> ukbd0 at uhidev0: 8 variable keys, 6 key codes
>>> wskbd1 at ukbd0 mux 1
>>> uhidev1 at uhub4 port 1 configuration 1 interface 1 "2.4G 2.4G
>>> Wireless Device" rev 1.10/10.01 addr 2
>>> uhidev1: iclass 3/1, 186 report ids
>>> ums0 at uhidev1 reportid 1: 5 buttons, Z and W dir
>>> wsmouse1 at ums0 mux 0
>>> uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0
>>> uhid1 at uhidev1 reportid 3: input=2, output=0, feature=0
>>> uhid2 at uhidev1 reportid 4: input=1, output=0, feature=0
>>> uhid3 at uhidev1 reportid 186: input=31, output=31, feature=0
>>> vscsi0 at root
>>> scsibus2 at vscsi0: 256 targets
>>> softraid0 at root
>>> scsibus3 at softraid0: 256 targets
>>> sd1 at scsibus3 targ 1 lun 0: <OPENBSD, SR CRYPTO, 006>
>>> sd1: 114470MB, 512 bytes/sector, 234435953 sectors
>>> root on sd1a (fc79adbb28d62767.a) swap on sd1b dump on sd1b
>>> inteldrm0: 1366x768, 32bpp
>>> wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation), using
>>> wskbd0
>>> wskbd1: connecting to wsdisplay0
>>> wsdisplay0: screen 1-5 added (std, vt100 emulation)
>>> alc0: could not disable RxQ/TxQ (0xffffffff)!
>>> alc0: could not disable Rx/Tx MAC(0xffffffff)!
>>> alc0: master reset timeout!
>>> alc0: reset timeout(0xffffffff)!
>>>
>>> The net is not accessible.If I remove the bank the net is OK.
>>>
>>> Why?Any idea?
>>> Thanks.
>>> Luciano.
>>
>>
>
No comments:
Post a Comment